Adjustments and Tests
173
Loading Software if Flash Contains Only Boot Code
If the flash memory contains only boot code (for example, if it is new), or if a
download was interrupted (for example, by a power outage) you must
download software through the printer’s parallel port using the three-key
initialization sequence covered in this section.
1.
Make sure the printer’s parallel port is available. In some configurations,
you may have to re-install the Centronics® I/O cable and connector in
order to load basic software into the printer.
2.
Make a configuration printout of all saved configurations. (Refer to the
User’s Manual.)
3.
Set the printer power switch to O (Off).
4.
Disconnect the data (signal) cable(s) from the printer interface
connectors.
5.
Connect a parallel data printer cable to the LPT1 port of an IBM-
compatible computer running the PC-DOS, MS-DOS, or Windows (3.1x,
95, 98, Me, NT, 2000, or XP) operating system.
6.
Connect the data cable to the Centronics port of the printer.
7.
On the printer control panel, press and hold down the
ONLINE
+
FF + VIEW
keys. Without releasing the keys, power the printer
on.When you see “B01 STATUS: 8245 SDRAM TEST 32MB” on the
LCD, release the keys.
8.
Wait until you see “B20: STATUS 00% / DOWNLOAD MODE” or
“PROGRAM DOWNLOAD” on the LCD before doing the next step.
9.
Using Windows Explorer, create a directory named
download
at the root
level of your C: hard drive. (
C:\download
)
10. Insert the printer emulation software CD-ROM into your computer’s CD-
ROM drive.
11. Open the readme.txt file on the CD-ROM. There are emulation sets with
corresponding part number files from which to choose. All emulations
include the program file or emulation code. They are offered in two file
formats: .exe and .prg.
Use .exe files to download through the parallel
port.
12. Identify which emulation set you want to load into the printer and note the
filename that corresponds to that emulation. The filename is a six digit
number plus
.exe
. For example: 123456.exe
This is the file you will download into the printer.
13. Copy the file to the
download
directory you created in step 8.
14. Start a command prompt session. (The Start Menu icon is usually labeled
MS-DOS Prompt
or
Command Prompt
.)
15. At the command prompt type:
C:
<Enter>
cd \download
<Enter>
Summary of Contents for 6600 Series
