SysKonnect SK-4590 Installation Manual Download Page 19 | Manualshive

Page: 19 / 69

background image

Installation Instructions

19

SK-NET TR/PCI (+) (SK-459x)

Token Ring PCI NIC

Chapter 2. Installing the
Adapter

5.

Replace the computer cover, reconnect the power cord and plug it into the power outlet.
Connect the adapter to the network using the appropriate cable.

6.

Install the required protocol driver in accordance with the instructions in the README
Viewer.

«
...
17
18
19
20
21
...
»

Summary of Contents for SK-4590






































































Reviews:

No comments

Related manuals for SK-4590

Brand: Lanner Pages: 2

Brand: Tripp Lite Pages: 2

Brand: BSD Networks Pages: 7

Brand: Patton electronics Pages: 12

Brand: Jøtul Pages: 20

Brand: TRENDnet Pages: 62

Brand: Schrack Technik Pages: 2

Speedway Revolution

Brand: impinj Pages: 60

Brand: Eaton Pages: 14

ConnectX-3 Pro MCX349A-XCCN

Brand: Mellanox Technologies Pages: 35

Brand: Moxa Technologies Pages: 36

IPLink 2603 Series

Brand: Patton Pages: 120

Brand: Tripp Lite Pages: 3

Brand: ZyXEL Communications Pages: 2

Brand: ZyXEL Communications Pages: 263

Brand: Helmholz Pages: 20

Brand: ADF Web Pages: 20

Brand: NAVI Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands