SysKonnect SK-4590 Installation Manual Download Page 2

Page: 2 / 69

Installation Instructions

SK-NET TR/PCI (+) (SK-459x)

Token Ring PCI NIC

Safety Information - Read This
First

First Edition (February 1996)
This edition applies to the SysKonnect products SK-NET TR/PCI (SK-4591) and SK-NET
TR/PCI+ (SK-4590) Token Ring PCI Network Interface Cards. Right of technical
modifications reserved.

We would like to receive comments on this publication. Please address your comments to:

SysKonnect
Information Development
Siemensstraße 23
76275 Ettlingen
Germany

FAX:

(49) 72 43 50 29 89

INTERNET: [email protected]

Trademarks
Product names mentioned herein may be trademarks and/or registered trademarks of their
respective companies.

Warranty and Software License
Contracts are included in this documentation.



a business unit of Schneider & Koch & Co. Datensysteme GmbH.
All rights reserved

Summary of Contents for SK-4590






































































Search results

Summary of Contents for SK-4590

Reviews:

Related manuals for SK-4590

Brands by name

Popular brands

SysKonnect SK-4590, Installation Manual

Search results

Summary of Contents for SK-4590

Reviews:

Related manuals for SK-4590

Brands by name

Popular brands