background image

Page 

2

 of 

26

 

 

This document is intended for Symantec support personnel, IBM, or other authorized Symantec Service 
Partners.  

Symantec Corporation 

 

Address:  350 Ellis St., Mountain View, CA 94043  

Website:  

http://www.symantec.com

 

 

Copyright © Symantec Corporation. 2011. All rights reserved.  

No part of this document may be reproduced or transmitted in any form or by any means without prior 
written consent of Symantec Corporation.  

Trademarks and Permissions  

and other Symantec trademarks are trademarks of Symantec Corporation. 

 

All other trademarks and trade names mentioned in this document are the property of their respective 

holders.  

Notice 

 

The purchased products, services and features are stipulated by the contract made between Symantec 

and the customer. All or part of the products, services and features described in this document may not 

be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all 

statements, information, and recommendation in this document are provided “AS IS” without warranties, 

guarantees or representation of any kind, either express or implied.  

The information in this document is subject to change without notice. Every effort has been made in the 

preparation of this document to ensure accuracy of the contents, but all statements, information and 

recommendations in this document do not constitute the warranty of any kind, express or implied.  

 

 

 

Summary of Contents for SIEM9750



























Reviews: