background image

3

Installing the 4-port Adapter

3-10 Sylantro 4-Port Adapter Installation Guide

Making the Network Connections

To connect the adapter to the customer’s LAN, connect one end of the network cable 
to the Ethernet port on the back of the 4-port adapter and the other end to a nearby 
LAN outlet or directly to the Ethernet switch as displayed in Figure 3-2.

Figure 3-2

Ethernet Switch Connections

The incoming broadband IP line that comes from the service provider needs to be 
connected to a device that converts the incoming line to 10/100-BaseT Ethernet. The 
10/100-BaseT line is then connected to an Ethernet switch. The network 
connections are made using Category 5 Ethernet cables.

This configuration applies to any incoming broadband connection such as a DSL 
line or T1/E1 line from the service provider. The network connection provided by 
the service provider should have sufficient bandwidth to support the customer data 
and voice requirements. For more information on bandwidth requirements, refer to 
“Bandwidth Requirements” on page 2-4.

Note:

Make sure the service provider network connection is already 

installed and verified before the adapter is installed.

Ethernet switch

Integrated

access device

Incoming 

network 

termination

Data network

LAN outlet (optional)

Adapter (front)

CA-204

STATUS

TX LNK RX

1

2

3

4

The adapter can also be connected 
directly to the Ethernet switch.

4port_adapter_net_connect1

Summary of Contents for 4-Port Adapter















































Reviews: