SUNWARD SWE215F-5 Operation & Maintenance Manual Download Page 55

Page: 55 / 182

OPERATION & MAINTENANCE MANUAL SWE215F

3.2.2 Pilot Safety Lever

Warning



When leaving the cab, always set the pilot

pilot safety lever (1) to LOCK position.

Failure to do so as well as to touch the lever

accidentally, serious injury may occur.



If the pilot safety lever is not set to LOCK

position, there is a possibility that it will

move and lead to serious accidents or

injury. The specification of these control

levers is shown in fig.



When operating the pilot safety lever

upward or downward, pay attention not to

touch the other control levers.

Pilot safety lever is a device being used to lock up

working equipment and control levers for swing, travel

and accessories (if equipped). Pull the lever to lock

up. .

Pilot safety lever is pilot hydraulic lock device. Even if

it’s in locked position, the control lever for working

equipment and travel control lever are movable. But

working equipment, travel motor and swing motor

stop.

Summary of Contents for SWE215F-5























































































































































































Search results

Summary of Contents for SWE215F-5

Reviews:

Related manuals for SWE215F-5

Brands by name

Popular brands

SUNWARD SWE215F-5, Operation & Maintenance Manual

Search results

Summary of Contents for SWE215F-5

Reviews:

Related manuals for SWE215F-5

Brands by name

Popular brands