manualshive.com logo in svg

STILLE 530-1700, Service And Technical Manual, Page: 76 / 80

Share
Download
STILLE 530-1700 Service And Technical Manual Download Page 76

76

          Stille imagiQ2

TM

 service manual   Technical

Technic

al

     

Testprotocol according to ISO -EN 62353

The “REFERENCE VALUE” from the first test before putting into service together with the measuring method shall be documented as a refe-
rence for future measurements. Before testing, the ME EQUIPMENT shall be disconnected from the SUPPLY MAINS. All DETACHABLE POWER 
SUPPLY CORDS shall be inspected.  It is recommended to follow the sequence of testing described by figure Figure B.1 in the standard.
Measurement of APPLIED PART LEAKAGE CURRENT is not requires, the device is classified as TYPE B APPLIED PART.
Nominel test measures are described in the standard.

Testing organisation:

Test before putting into service (reference value)     

    

Recurrent test                

     

Test after repair   

Name of testing person:

Model:                                imagiQ2

Serial number:

Applied part type:                   B

Mains connection:            DPS

Measuring method:  

(Direct method according to 5.3.3.2.3 or 

                                                             5.3.3.3.3 in the standard is recommeded)

Accessories:

Test:
Measurement equipment:

Complies:
         Yes                         No

Visual inspection:

Measurements:                                                                                                                           measured value

Protective earth resistance                                                                                                            ______ 

Equipment leakage current (according to Figure ___ )                                                               ______ mA

Patient leakage current (according to Figure ___ )                                                                     ______ mA

Insulation resistance (according to Figure ___ )                                                                          ______ Mohm

Functional test (parameters tested):

Overall assessment use ISO -EN 62353 §4.3 as guideline for assessment

:

Where there any safety or functional deficiencies detected during the test!

Where there any risks directed, deficiencies detected may be corrected on short term!

If any deviatiosn were detected the equipment shall be taken out of operation until deficiencies are 
corrected!

Equipment does not comply - Modification / Exchange of components / Taking out of service - is 
recommended!

Next recurrent test necessary in 1 year or 2000 hours service, whichever comes first.

It is recommended that the device is marked tested OK/ not Ok after test and if possible, when the next test shall be performed.

Date and signature of test person:

__________________________________________________________________________________

Summary of Contents for 530-1700

















































































Reviews:

No comments