manualshive.com logo in svg

STILLE 530-1700, Service And Technical Manual, Page: 45 / 80

Share
Download
STILLE 530-1700 Service And Technical Manual Download Page 45

45

Stille imagiQ2

TM

 service manual   Technical

Technic

al

   

TROUBLE SHOOTING GUIDE

Hydraulic problems floor locks parking cylinders

Symptom

Probable cause

Procedure

The table can be parked but 
the pump motor continues 
for approx. 15 seconds. and 
an error indication (alterna-
tely blue/green) flashes on 
the hand control after the 
motor has stopped. Panning 
does not function.

Connector (PX)  on the main 
board is not correctly con-
nected. 

a. Check the connector.

The blue/green lamps with 
the symbols for locked/open 
lock begin to flash alterna-
tely after the table has been 
parked a time. 

a. Incorrectly adjusted posi-
tion switches 

b. Leak in the hydraulic 
parking circuit. 

c. position switches unservi-
ceable.  

a. Adjust the position swit-
ches.

b. Trace any leak in the 
hydraulic parking circuit.

c. Replace the position swit-
ches.

The pump motor runs for 
approximately 15 seconds 
after an attempt has been 
made to park the table or 
adjust the lateral tilt/set the 
zero position, and a fault indi-
cation for parking (alterna-
tely blue/green) is presented 
after the motor stops. Pan-
ning is possible.

a. Cable not correctly con-
nected to the position swit-
ches. 

b. Incorrectly adjusted posi-
tion switches. 

c. Leak in the hydraulic par-
king circuit.

d. Position switches not 
giving signal. 

a. Check the cable connec-
tions.

b. Adjust the position swit-
ches. 

c. Trace any leak in the 
hydraulic parking circuit. 

d. Replace the position swit-
ches.

Summary of Contents for 530-1700

















































































Reviews:

No comments