manualshive.com logo in svg

STILLE 530-1700, Service And Technical Manual, Page: 39 / 80

Share
Download
STILLE 530-1700 Service And Technical Manual Download Page 39

39

Stille imagiQ2

TM

 service manual   Technical

Technic

al

   

TROUBLE SHOOTING GUIDE

Electrical problems, indications on the hand control unit

Symptom

Probable cause

Procedure

Blue ”Charging in progress” 
lamp on the hand control 
does not illuminate when the 
mains voltage power cable is 
connected.

First withdraw the plug from 
the wall socket and inspect 
the mains voltage power 
cable. A damaged cable can 
become the cause of injury or 
death. 

a. The cable is not correctly 
connected  

b. The main power switch on 
the table is switched off. 

c. There is no voltage at the 
wall socket. 

d. The primary fuse (s) on the 
table has (have) blown. . 

e. The signal cable from the 
battery charger is not cor-
rectly connected to the con-
trol unit, (PX).

f. The battery charger is 
unserviceable 

g. The control unit is unservi-
ceable. 

A damaged cable must be 
replaced immediately. Use a 
Stille original cable only.

a. Check the cable connection 

b. Check the main power 
switch.

c. Check that there is voltage 
at the wall socket. 

d. Check the primary fuse(s) 
on the table. 

N.B. The fuse values for  
100/ 120/ 230 V are dif-
ferent.

e. Check the connection of 
the signal cable. (PX).

f. Replace the main bord. 

g. Replace the control unit. 

Summary of Contents for 530-1700

















































































Reviews:

No comments