Still EXD 18 Original Instructions Manual Download Page 46

Page: 46 / 146

Checking the brake

CAUTION

Perform this check on a flat surface.

–

Drive the truck and whilst tilting the tiller in

areas (1) and (2), test the effectiveness of

the brake.

In these two areas, the truck is braked and the

drive unit is no longer powered. Releasing the

tiller in the drive area (2) sends the tiller into

the (1) area and cuts traction.

Check emergency shutdown

–

Pull the emergency stop handle (1).

–

The power supply to the machine is cut off.

–

The electrical controls and motors are no

longer supplied.

–

The electromagnetic brake is applied.

–

Press in the emergency stop handle (1)

then enter the code or turn the switch key to

have the functions available again.

NOTE

Ensure the stabiliser wheels operate correctly.

This influences braking effectiveness.



Use

Checks and actions prior to commissioning

1160 801 15 51 EN - 02/2021 - 11

Summary of Contents for EXD 18



















































































































































Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands

Still EXD 18, Original Instructions Manual

Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands