Still EXD 18 Original Instructions Manual Download Page 128

Page: 128 / 146

Lift mast

Lifting device

–

Remove any dirt from the guide rails (1).

–

Lubricate the guide rails of the outer, central

and inner masts using pressure high resist-

ance adhesive lubricant to slow down wear.

NOTE

Lubricate the guide rails uniformly using an

aerosol spray at a distance of 15 to 20 cm.

Wait approximately 15 minutes before restart-

ing the truck.

–

Coat the chain (2) with spray for chains.

–

Lubricate the various bearings and friction

points with oil.

Servicing the lift mast

–

Raise the fork carriage and ensure that it

cannot lower unexpectedly.

Checking the lift cylinders and connec-

tions for leaks

–

Visually check the hydraulic connections

and cylinders for leaks.

–

Tighten any leaking connections and repair

faulty cylinders.



Maintenance

Lift mast

118

1160 801 15 51 EN - 02/2021 - 11

Summary of Contents for EXD 18



















































































































































Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands

Still EXD 18, Original Instructions Manual

Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands