Still EXD 18 Original Instructions Manual Download Page 88

Page: 88 / 146

Phase

Green LED

Red LED

Disconnected

mains socket Off

Off

Charging

phases

Flashing

Off

Stopped /

Equalisation /

Maintenance

phase

Continuously

lit

Off

Charging too

long

Off

Continuously

lit

Charger po-

larity reversed

(+battery and

-battery

charger ca-

bles reversed,

with the bat-

tery remain-

ing normally

connected to

the truck as-

sembly)

Continuously

lit

Continuously

lit

Polarity inver-

sion of the

battery

Off

Selector in

neutral posi-

tion

Flashing

CAUTION

It is strictly prohibited to use an on-board charger

other than the one recommended.

CAUTION

Risk of damage to the mains cable due to frequent

operator handling. Risk of electric shock and/or

burns!
The mains cable must be checked regularly as part

of periodic statutory checks and maintenance opera-

tions.

NOTE

Use

Handling the battery

1160 801 15 51 EN - 02/2021 - 11

Summary of Contents for EXD 18



















































































































































Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands

Still EXD 18, Original Instructions Manual

Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands