Still EXD 18 Original Instructions Manual Download Page 16

Page: 16 / 146

Internet address and QR code

The information can be accessed at any time

by pasting the address https://m.still.de/vdma

in a web browser or by scanning the QR code.

Eco-design requirements for

electric motors and variable

speed drives

All motors in this industrial truck are exempt

from Regulation (EU) 2019/1781 because

these motors do not meet the description giv-

en in Article 2 "Scope", Item (1) (a) and be-

cause of the provisions in Article 2 (2) (h) "Mo-

tors in cordless or battery-operated equip-

ment" and Article 2 (2) (o) "Motors designed

specifically for the traction of electric vehicles".
All variable speed drives in this industrial truck

are exempt from Regulation (EU) 2019/1781

because these variable speed drives do not

meet the description given in Article 2

"Scope", Item (1) (b).



Introduction

Eco-design requirements for electric motors and variable speed drives

1160 801 15 51 EN - 02/2021 - 11

Summary of Contents for EXD 18



















































































































































Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands

Still EXD 18, Original Instructions Manual

Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands