Still EXD 18 Original Instructions Manual Download Page 61

Page: 61 / 146

Disconnecting a truck equipped with

the FleetManager™ option

NOTE

Operators must not log off intentionally while

driving.

WARNING

Access to the truck must be disabled.
Unauthorised users are not allowed to use the truck.

Disconnecting a truck equipped with a

keypad or electronic key

–

Park the truck in a safe place.

–

Press the button (3) to log off. Keep the but-

ton pressed in.

No LEDs light up. A long acoustic signal

sounds.
The LED (1) lights up for a second (red col-

our). The LED (2) is not lit. A long acoustic

signal sounds.
The LED (1) is no longer lit. The LED (2) flash-

es slowly at two-second intervals (green col-

our). No acoustic signal sounds.
The truck is disabled.

–

Turn the switch key to the off position to

switch the truck off completely.



Use

Operating the FleetManager™ option

1160 801 15 51 EN - 02/2021 - 11

Summary of Contents for EXD 18



















































































































































Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands

Still EXD 18, Original Instructions Manual

Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands