Still EXD 18 Original Instructions Manual Download Page 14

Page: 14 / 146

EC declaration of conformity

Declaration

STILL GmbH

Berzeliusstrasse 10

22113 Hamburg

GERMANY

We declare that the machine

Industrial truck

according to these operating instructions

Model

according to these operating instructions

conforms to the latest version of the Machinery Directive 2006/42/EC.

Person authorised to compile the technical documents:

See EC compliance declaration

STILL S.A.S.

The manufacturer declares that the truck com-

plies with the requirements of the EC direc-

tives valid at the time of marketing. This is

confirmed by the EC declaration of conformity

and by the EC labelling on the nameplate.
An independent structural change or addition

to the truck can compromise safety, thus inva-

lidating the EC declaration of conformity.
The EC declaration of conformity must be

carefully stored and made available to the rel-

evant authorities.

Introduction

EC declaration of conformity

1160 801 15 51 EN - 02/2021 - 11

Summary of Contents for EXD 18



















































































































































Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands

Still EXD 18, Original Instructions Manual

Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands