49
ENGLISH
GB
squeeze in the oil.
3. Lift out the paper filter N and thoroughly clean
the air filter housing to prevent dirt from entering
the carburettor.
4. Clean the paper filter as follows: Knock it light-
ly against a flat surface. If the filter is very dirty,
change it.
5. Assemble in the reverse order.
Petroleum-based solvents such as kerosene must
not be used for cleaning the paper filter as these
can destroy the filter.
Do not use compressed air for cleaning the paper
filter. The paper filter must not be oiled.
KEEP ENGINE CLEAN
The engine is air cooled. A blocked air system will
damage the engine.
The cylinder cooling flanges and air inlet should
be cleared of grass and dirt every 5 hours or every
day (fig 20 - 21). This is particularly important
when mowing dry grass.
The area around the silencer should be cleaned in
order to prevent fire.
Use compressed air or a brush for cleaning. Do not
clean the engine with water.
During prolonged mowing of dry grass, the inner
cooling fins on the engine may require cleaning.
Contact an authorised service centre.
SPARK PLUG
Check and clean the spark plug after 100 running
hours.
Clean the spark plug using a wire brush (do not
sand blast) and reset the spark gap to 0.75 mm.
Replace the sparking plug if the electrodes are bad-
ly burnt. For replacing a sparking plug, a sparking
plug sleeve AC and torsion pin AD are provided in
the plastic bag containing accessories (only on
Garden).
The engine manufacturer recommend:
Scoop:
Champion RC12YC.
Garden:
Champion J19LM.
CARBURETTOR
The carburettor is correctly adjusted when it leaves
the factory and any other adjustments are generally
not needed.
Despite this, if the carburettor needs adjusting con-
tact a service centre.
ADJUSTING THE CLUTCH/BRAKE
If the drive belt slides (it can stretch a little if worn)
there is an adjuster on the clutch/brake rod.
Adjust: Move the locking pin O to the rear hole
(fig 22).
The brakes are adjusted using nut P on the brake
arm (fig 22).
After adjustment, make sure the clutch is always
activated before the brake.
DISMANTLING THE MOWER DECK
1. Engage the parking brake.
2. Lift the machine on its bumper.
If the machine is to be stood on its side,
the petrol and engine oil must first be
drained off. In addition, the battery
must be removed from Garden models.
3. Set the lowest cutting height and remove the
locking pin Q (fig 23).
4. Dismantle the two rear locking pins R and the
cable to the switch on the mower deck (fig 24).
5. Pry-off the v-belt from the pulley (bend the belt
guide S upwards) (fig 25).
6. Lift off the mower deck.
CHANGING THE V-BELT
ENGINE - MOWER DECK
1. Dismantle the mower deck (see above).
2. Remove the belt holder T. Lift off the old belt
(fig 26).
3. Fit a new genuine v-belt in the reverse order.
CHANGING THE V-BELT
ENGINE - TRANSMISSION
1. Engage the parking brake.
2. Lift the machine on its bumper.
If the machine is to be stood on its side,
the petrol and engine oil must first be
drained off. In addition, the battery
must be removed from Garden models.
3. Dismantle the mower deck (see above).
Summary of Contents for Garden Scoop
