SteelMax Torch Runner Operator'S Manual Download | Manualshive

Page: 23 / 42

background image

Torch Runner (HS)

Torch Runner (HS) Operator’s Manual

23

5.9. Left and right heat protection shield

Additionally protect the carriage from the influence of a high temperature. Install as

shown in the figure below.

5.10. Bottom heat protection shield

Additionally protects the carriage from the influence of a high temperature. To install,

loosen five screws with the 3 mm hex wrench, slide the shield under the heads of the

screws according to the direction of the arrow, and then tighten the screws.

Part number: OSL-0475-53-00-00-0

Screws for fixing the bottom shield

Part number:
OSL-0475-54-00-00-0

Part number:
OSL-0475-55-00-00-0

«
...
21
22
23
24
25
...
»

Summary of Contents for Torch Runner











































Reviews:

No comments

Related manuals for Torch Runner

Brand: Tanaka Pages: 72

Carlyle Tools 6-3802A

Brand: Napa Pages: 16

Brand: Swisher Pages: 30

Brand: Jonsered Pages: 32

Brand: Jonco Pages: 15

Brand: Jonsered Pages: 44

Brand: QEP Pages: 8

Brand: Stiga Pages: 2

Brand: Maruyama Pages: 32

Brand: Maruyama Pages: 56

Brand: Maruyama Pages: 60

Brand: N.KO Pages: 16

Brand: WilTec Pages: 17

Brand: Sirman Pages: 8

Brand: CanyCom Pages: 63

Brand: Breadman Pages: 8

Brand: Maruyama Pages: 76

Brand: RASOR Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands