SteelMax Torch Runner Operator'S Manual Download | Manualshive

Page: 26 / 42

background image

Torch Runner (HS)

Torch Runner (HS) Operator’s Manual

26

5.13. Gas manifold (for oxy-fuel cutting)

Provides

safe

gas delivery to 2- or 3-hose torches. Manifolds are available with or

without gas cut-off valve in both metric and imperial versions.

2/3 manifold with cut-off valve
(metric):
RZD-0475-66-00-00-0

3/3 manifold with cut-off valve
(metric):
RZD-0475-72-00-00-0

1/4’’ RH

2/2 manifold (metric):
RZD-0475-64-00-00-0

2/3 manifold (metric):
RZD-0475-63-00-00-0

2/2 manifold with cut-off valve
(metric):
RZD-0475-65-00-00-0

3/3 manifold (metric):
RZD-0475-74-00-00-0

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

3/8’’ LH

1/4’’ RH

1/4’’ RH

1/4’’ RH

1/4’’ RH

«
...
24
25
26
27
28
...
»

Summary of Contents for Torch Runner











































Reviews:

No comments

Related manuals for Torch Runner

Klauke AXELENT EBS6GKSNGBAX

Brand: Textron Pages: 11

Brand: RASOR Pages: 15

Brand: Mafell Pages: 102

crease matic 150

Brand: KAS Pages: 10

PEGAS 121 PLASMA

Brand: Alfa IN Pages: 22

Brand: Mafell Pages: 114

Brand: VITO GARDEN Pages: 20

Brand: Stanley Pages: 36

Ideal Cutter 4810

Brand: ABC Office Pages: 8

Brand: Maruyama Pages: 32

Brand: Maruyama Pages: 56

Brand: Maruyama Pages: 60

Brand: Land Pride Pages: 38

Brand: Land Pride Pages: 40

Brand: Binks Pages: 12

Brand: Xhorse Pages: 23

Hurricane F-550G

Brand: Vari Pages: 48

Brand: Efco Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands