42
43
RADIO INTERFERENCE
This microwave oven may cause interference to your radio, TV, or similar equipment.
When interference occurs,
it may be eliminated or reduced by the following procedures.
a. Clean the door and sealing surface of the oven.
b. Place the radio, TV, etc. as far away from your microwave oven as possible.
c. Use a properly installed antenna for your radio, TV, etc. to get stronger
signal reception.
Installation
1. Make sure all the packing materials are removed from the inside of the microwave
door.
2. Inspect the oven after unpacking for any visual damage such as: Misaligned Door,
Damaged Door, Dents or Holes in Door Window and Screen, Dents in Cavity
If any of the above are visible, DO NOT use the oven.
3. This Microwave Oven weighs 22 kg and must be placed on a horizontal surface
strong enough to support this weight
WARNING-THIS APPLIANCE MUST BE EARTHED.
1. Ensure the plug socket is within easy reach for the power cord. DO NOT force the
cord over a significant distance or stretch the cord excessively
2. This oven requires 1.5 KVA for its input. Please consult an authorised service agent
for any installationrequirements
4. The oven must be placed away from high temperature areas and steam.
5. DO NOT place anything on top of the oven.
6. DO NOT remove the turn -table drive shaft.
CAUTION: This oven is protected internally by ac 250V,10 Amp Fuse.
Important
The wires in this mains lead are coloured in accordance with the following code:
Green and Yellow: Earth
Blue:
Neutral
Brown:
Live
As the colours of the wires in the mains leads of the appliance may not correspond
with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in
the plug which is marked with the letter E or by the earth symbol coloured green of
green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked
with the letter N or coloured black. The wire which is coloured brown must be con-
nected to the terminal which is marked with the letter L or coloured red.
OPERATING YOUR MICROWAVE
1. Single Button Heating
With the press of a button you can heat everyday items quickly and conveniently
Place desired item on turntable
∙
Press the “Start/Reset” button, the microwave will heat at 100% for 1 minute
∙
You will hear 5 beeps at the end of the cooking cycle
∙
Standard Operation
There are two methods of heating using this microwave. Automatic and Manual
2. Automatic Heating
Automatic heating will run the microwave at 100% power for a time specified by you.
Set the timer to your desired length using the “Defrost/Timer”. Turn to the right for
∙
heating
Press the “Start/Reset” button. The microwave will run at 100% power for the time
∙
length selected
3. Manual Heating
With Manual operation you can select both the power at which the microwave will
run and the time.
Press the “Micro” button until the display reads the desired power setting
The power settings read as follows on the microwave display.
P100 – 100% power (see fig.1)
P70 – 70% power
P50 – 50% power
P30 – 30% power
P10 – 10% power
The red bar at the base of the
microwave display screen (see fig. 2)
also shows the corresponding power
level.
1. Use the control dial called “Defrost/Timer” to select the desired time
length for heating (00.10 – 60.00 minutes)
2. Press the “Start/Reset” button to begin.
3. The microwave will now cook at the selected power level and time length.
4. Auto Weight Defrost
Your microwave can also be used to defrost based on the weight of the desired item
E.g. 0.5 kg of meat:
1. Rotate the “Defrost/ Timer” control dial to the left until the display read 0.5
2. Press “Start/Reset” The microwave will now begin to defrost at a set time
length and power setting
8
1.Single Button Heating
With the press of a button you can heat everyday items quickly and conveniently
1. Place desired item on turntable
2. Press the “Start/Reset” button, the microwave will heat at 100% for 1 minute
3. You will hear 5 beeps at the end of the cooking cycle
Standard Operation
There are two methods of heating using this microwave. Automatic and Manual
2. Automatic Heating
Automatic heating will run the microwave at 100% power for a time specified by you.
1. Set the timer to your desired length using the “Defrost/Timer”. Turn to the right for heating
2. Press the “Start/Reset” button.
The microwave will run at 100% power for the time length selected
3. Manual Heating
With Manual operation you can select both the power at which the microwave will run and the time.
Press the “Micro” button until the display reads the desired power setting
The power settings read as follows on the microwave display.
P100 – 100% power (see fig.1)
P70 – 70% power
P50 – 50% power
P30 – 30% power
P10 – 10% power
The red bar at the base of the microwave display screen (see fig. 2) also shows the corresponding power level.
1. Use the control dial called “Defrost/Timer” to select the desired time length for heating (00.10 – 60.00
minutes)
2. Press the “Start/Reset” button to begin.
3. The microwave will now cook at the selected power level and time length.
Fig.2
Fig.1
OPERATING YOUR MICROWAVE
