SRAM RockShox RS-1 Service Manual Download Page 41 | Manualshive

Page: 41 / 59

background image

41

Accelerator Damper Removal

Remove the stanchion from the carbon fiber upper.

If the stanchion does not slide out of the carbon fiber upper, the press fit of
the shaft may still be engaged. Reinstall the bottom bolt 2 to 3 turns and
repeat the previous step.

Insert the anchor tool into the bottom of the carbon fiber upper so that it
engages the damper anchor on the Accelerator Damper.™

Rotate the anchor tool

clockwise

and unthread the Accelerator Damper

assembly.
Remove the anchor tool from the carbon fiber upper.

The XLoc™ hose will spin as you loosen the anchor from the carbon fiber
upper. This is normal.

Guide the XLoc hose through the grommet while pulling down on the
anchor tool to reveal the Connectamajig.™
Remove the anchor tool.

4

Anchor tool

5

30 mm & anchor tool

6

Anchor tool

7

«
...
39
40
41
42
43
...
»

Summary of Contents for RockShox RS-1




























































Reviews:

No comments

Related manuals for RockShox RS-1

Brand: zenitech Pages: 16

Action Replay DSi

Brand: Datel Pages: 2

Brand: Eaton Pages: 2

AdvancedPunch Pro

Brand: GBC Pages: 92

Brand: UNIT 1 Pages: 23

Brand: Kabuto Pages: 16

Brand: Kargo Master Pages: 13

Brand: Kargo Master Pages: 21

Brand: Kargo Master Pages: 4

Brand: Karel Pages: 56

Brand: Oki Pages: 4

XMODS Custom RC

Brand: Radio Shack Pages: 4

Sleeptrainer Palm the penguin

Brand: NENKO Pages: 4

Brand: Solight Pages: 2

Brand: Burley Pages: 16

Brand: DYNATEK Pages: 4

Brand: Gira Pages: 4

Brand: Phonocar Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands