SRAM RockShox RS-1 Service Manual Download | Manualshive

Page: 30 / 59

background image

30

Bleed Procedure

Reposition the Charger 2 Damper™ in the vise at an angle with the bleed
port angled as upward as possible.
Install the bottom bolt into the rebound damper shaft 3-4 turns.

Fill a bleed syringe half full with suspension oil. Slowly depress the plunger
to remove any air bubbles from the syringe.

NOTICE

Only use the syringe included with the RockShox Standard or Charger
Bleed kit. Do not use syringes that have been in contact with DOT brake
fluid. DOT brake fluid will permanently damage the damper.

Thread the syringe into the seal head bleed port.
Depress the plunger to pressurize the damper assembly.

Push the rebound damper shaft down. Keep pressure on the plunger as
the syringe fills with oil. Pull up slowly on the rebound damper shaft. Keep
pressure on the syringe as oil fills the system.

Repeat pushing and pulling the rebound damper shaft, keeping pressure on
the plunger, until only small bubbles emerge from the damper.

9

10

3wt

RockShox® standard bleed syringe

11

12

«
...
28
29
30
31
32
...
»

Summary of Contents for RockShox RS-1




























































Reviews:

No comments

Related manuals for RockShox RS-1

Brand: Voxx Pages: 7

Brand: Wallenstein Pages: 31

Brand: Larry vs Harry Pages: 20

Brand: NEC Pages: 5

Brand: Panasonic Pages: 2

Brand: Samsung Pages: 88

Brand: Samsung Pages: 215

Brand: Bartington Pages: 11

Brand: ICC Pages: 32

Brand: iDataLink Pages: 30

Brand: IFM Electronic Pages: 16

Brand: IFM Electronic Pages: 6

Brand: Lantus Pages: 5

Brand: yasuni Pages: 11

Brand: Lanier Pages: 3

Brand: Paradox Pages: 2

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

Brand: aci Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands