SRAM RockShox RS-1 Service Manual Download | Manualshive

Page: 47 / 59

background image

47

Accelerator Damper™ Service

Remove the damper seal head o-ring. Use a pick to pierce and remove the
rod wiper seal.
Apply grease and install a new o-ring and rod wiper seal.

Install the stepped face of the rod wiper seal into the threaded end of the
seal head.

Remove the glide ring

from the Dig Valve™. Install a new glide ring.

Install the damper seal head onto the rebound shaft with the threads
oriented toward the piston.

NOTICE

Do not allow the outer lip of the rod wiper seal to fold over when installing
the damper seal head onto the rebound shaft.

12

13

14

«
...
45
46
47
48
49
...
»

Summary of Contents for RockShox RS-1




























































Reviews:

No comments

Related manuals for RockShox RS-1

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 54

Toughbook CF-F8EWDZZAM

Brand: Panasonic Pages: 20

Brand: Samsung Pages: 88

Brand: Samsung Pages: 215

Brand: UNIT 1 Pages: 23

Brand: Kabuto Pages: 16

Brand: OFFCARR Pages: 12

Brand: OEM Tools Pages: 4

E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital...

Brand: Olympus Pages: 2

AS4000 - AS Transcription Kit

Brand: Olympus Pages: 24

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Brand: Firecom Pages: 8

Brand: GLOBAL FITNESS & LEISURE Pages: 18

Brand: Horn Tools Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands