manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Operation Manual

Share
Download
Spectris Particle Measuring Systems LiQuilaz II E Operation Manual Download Page 82

Appendix D Ethernet Communications Overview

LiQuilaz II E and S Operations Manual

Page D-9

Figure D-5  Internet Protocol (TCP/IP) Properties

 window

d.

Record the existing settings on the 

Internet Protocol (TCP/IP) Properties

 

window.  
These settings will need to be restored after the instrument communication 
session is complete.

e.

Change the settings on the 

Internet Protocol (TCP/IP) Properties

 window to 

use the network address and mask determined above. See 

Figure D-5

 on page 

-9 for an example. The 

Default gateway

 and 

DNS server

 values should be left 

blank.

f.

Click the 

OK

 button to close the 

Internet Protocol (TCP/IP) Properties

 window.

g.

Click the 

OK

 button to close the 

Local Area Connection Properties

 window.

4.

The PC is now configured.

5.

Attach a network cable between the PC and the instrument.

6.

Use the procedure 

Troubleshooting Ethernet Connectivity 

on page

  D-4 to check 

the connection is functioning.

Summary of Contents for Particle Measuring Systems LiQuilaz II E














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands