manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Operation Manual

Share
Download
Spectris Particle Measuring Systems LiQuilaz II E Operation Manual Download Page 16

LiQuilaz II E and S Operations Manual

Page 2-1

Chapter 2
Unpacking and Connection

If the shipping container shows signs of damage such as crushing, depressions, water 
damage, etc. be sure to notify the shipper and Particle Measuring Systems before 
continuing. Notify Particle Measuring Systems at 1-877-475-3317, or 

[email protected]

. Follow any instructions you receive on how to proceed.

If the shipping container appears to be in good condition, continue to carefully unpack 
and inspect each item. Store the shipping container and its packing materials for use 
when returning the instrument for calibration or repair. This is important because an 
inadequate shipping container could void your warranty.

If anything is missing, contact Particle Measuring Systems Customer Response Center 
at 1-877-475-3317, or 

[email protected]

.

If all of the materials are included and undamaged, store the packing materials. It is 
important to keep these materials because warranties may not apply if return 
shipping containers are inadequate.

Unpacking

>> To unpack your shipment

1.

Open the container.

2.

Carefully remove the instrument and inspect it for damage.

3.

If the instrument has been damaged in shipment, notify the shipper and Particle 
Measuring Systems. Repackage the instrument in the original packing materials.

4.

If the instrument is not damaged, store the packing materials.

Summary of Contents for Particle Measuring Systems LiQuilaz II E














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands