manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Operation Manual

Share
Download
Spectris Particle Measuring Systems LiQuilaz II E Operation Manual Download Page 78

Appendix D Ethernet Communications Overview

LiQuilaz II E and S Operations Manual

Page D-5

a.

Is the cable bad? 

a.1

Try a different cable. 

a.2

If a direct laptop to instrument connection is being done, a cross-over cable 
may be required. Cross-over cables are specially marked as such. Particle 
Measuring Systems P/N 1000011477 is a cross-over cable.

b.

Is the other end of the cable alive?  
Does a known good device work when connected instead?

2.

Verify the device can talk using 

PING

. 

a.

Open a command shell on a PC, and type 

PING aaa.bbb.ccc.ddd  

where aaa.bbb.ccc.ddd is the address of the device.  
If there is no response, then there is an addressing problem.

Figure D-2  

Example for 

PING

 test

b.

Make sure the PC and the device being talked to are on the same network. 

c.

Check the PC’s address by opening a command shell and typing 

ipconfig

. 

c.1

Is the Mask the same on both the PC and the device?

c.2

Is the network portion of the address the same on both the PC and the 
device?

Summary of Contents for Particle Measuring Systems LiQuilaz II E














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands