manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Operation Manual

Share
Download
Spectris Particle Measuring Systems LiQuilaz II E Operation Manual Download Page 38

LiQuilaz II E and S Operations Manual

Page 4-1

Chapter 4
Operation

After the LiQuilaz II Liquid Particle Counter has been connected to its sample source, 
connected to the PC, and connected to electrical power it is ready to be run from the 
PC by means of Facility Net, Pharmaceutical Net, SamplerSight, or SamplerSight-
Pharma. 

User Interface (Controls, Data Display, Data Collection)

The user interface is the Particle Measuring Systems 

Facility Net

, 

Pharmaceutical Net

, 

SamplerSight

, or 

SamplerSight-Pharma

 software running on a separate PC. 

• A Syringe Sampler version of a LiQuilaz II instrument is connected to the PC 

through its sampler. 

• An Online version of a LiQuilaz II is connected to the PC directly with a 

communications cable.

After configuration, the user interface software controls all operating functions 
including the following:

• Sampling parameters: sample volume and sample interval (the interval between 

samples)

• Data collection

• Data display

• Alarms

All directions and options for configuring software are beyond the scope of this 
manual. See the appropriate software user’s manual for a full description of how to 
use the user interface software with samplers and particle counters: 

Facility Net User 

Manual, Pharmaceutical Net User Manual, SamplerSight User Guide, or SamplerSight-
Pharma User Guide.

Summary of Contents for Particle Measuring Systems LiQuilaz II E














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands