manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Operation Manual

Share
Download
Spectris Particle Measuring Systems LiQuilaz II E Operation Manual Download Page 12

LiQuilaz II E and S Operations Manual

Page 1-1

Chapter 1
Getting Started

The LiQuilaz® II E and S Series Liquid Particle Counters are sensors designed to 
measure particles in liquids. A sensor contains a liquid handling and optical system as 
well as electronics that measure the size of the particles sampled and transmit data to 
the data display system. 

The sensor requires AC power, connections to bring the liquid to the sensor, and a 
connection to a data display system. Particle Measuring Systems supplies several 
software packages that support the LiQuilaz II, including Facility Net, Pharmaceutical 
Net, SamplerSight, or SamplerSight-Pharma software.

The LiQuilaz II E Series Liquid Particle Counter has the following variations:

LiQuilaz II E20P 

A 20 mL per minute version that is intended for use with the SLS-2000 sampler.

LiQuilaz II E20 

A 70 mL per minute version that is intended for an online installation.

LiQuilaz II E15P 

A 20 mL per minute version that is intended for use with the SLS-2000 sampler or 
online installation.

The LiQuilaz II S Series Liquid Particle Counter has the following variations:

LiQuilaz II S05

A 80 mL per minute version with 0.5 µm sensitivity.

LiQuilaz II S03

A 80 mL per minute version with 0.3 µm sensitivity.

LiQuilaz II S02

A 50 mL per minute version with 0.2 µm sensitivity.

NOTE:

 

All S units are also available in a 20 mL per minute flowrate version.

Summary of Contents for Particle Measuring Systems LiQuilaz II E














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands