Sony XCL5005 Technical Manual Download Page 2

Page: 2 / 56

Table of Contents

Table of Contents

Features .................................................................. 3
Typical CCD Phenomena ..................................... 4
System Components .............................................. 5
Connection ............................................................. 6
Location and Function of Parts and Operation

.................................................................................. 7

Front/Top/Bottom ............................................... 7
Using a tripod ..................................................... 7
Rear .................................................................... 8
Connecting the cables ........................................ 9
Trigger signal specifications .............................. 9
DVAL/Exposure output specific (only DC IN

terminal) ......................................................... 10

Functions

1. CCD loaded on XCL-5005CR/5005 ..............11
2. Compatibility with previous model XCL-5000

...........................................................................12

3. Video output format .......................................13

3.1. Switching TAP  ........................................13
3.2. Color pixel array  .....................................13
3.3. Data order  ...............................................14

3.3.1. 1TAP 80 MHz .................................... 14
3.3.2. 2TAP 40 MHz .................................... 14

3.4. Port assignment .......................................15
3.5. Output data size ......................................15

4. Camera mode ..................................................16

4.1. Horizontal timing ....................................16
4.2. Vertical timing .........................................17

4.2.1. Normal mode ..................................... 17
4.2.2. Binning mode ..................................... 17
4.2.3. Partial scan mode ............................... 18
4.2.4. Trigger mode ...................................... 21
4.2.5. Trigger binning mode ......................... 22
4.2.6. Trigger partial scan mode ................... 23

5. Shutter setting ................................................25

5.1. Preset shutter ...........................................25
5.2. Arbitrary shutter setting ..........................26
5.3. Overlap ....................................................27
5.4. WEN-STRB ............................................27

6. DSP Operation ................................................28

6.1. Signal processing block chart .................28
6.2. Flip-flop

[XCL-5005]

...............................29

6.3. Digital clamp

[XCL-5005CR]

[XCL-5005]

.................................................................29

6.3.1. Clamp setting value ............................ 29
6.3.2. Correlation factor ............................... 29

6.4. Digital gain

[XCL-5005]

..........................29

6.5. Pixel gain

[XCL-5005CR]

.........................29

6.5.1. Definition equation ............................ 29
6.5.2. White balance ..................................... 30

6.6. Black balance

[XCL-5005CR]

..................30

6.6.1. Black balance automatic adjustment

method ................................................ 30

6.6.2. Black balance direct adjustment method

............................................................. 30

6.7. Gamma correction

[XCL-5005CR]

[XCL-5005]

.............................................. 31

6.7.1. Arbitrary setting method .................... 31
6.7.2. Five-point approximate linear

interpolation ....................................... 31

6.7.3. Coefficient input method .................... 32

6.8. 3 × 3 filter

[XCL-5005]

............................ 33

6.8.1. Mode 1 ............................................... 33
6.8.2. Mode 2 ............................................... 34

6.9. Edge detection/enhancement (DTL)

[XCL-5005]

.............................................. 35

6.10. Binarization

[XCL-5005]

......................... 36

6.11. Digital pedestal

[XCL-5005CR]

[XCL-5005]

................................................................. 37

6.12. 8/10/12 bit length selection

[XCL-5005CR]

[XCL-5005]

.............................................. 37

6.13. Grayscale chart

[XCL-5005]

.................... 37

6.14. Color chart

[XCL-5005CR]

...................... 38

Camera Control Commands

General ..................................................................39

Serial Communication Specifications ...............39
Command system .............................................39
Command format ..............................................39
Command input and response ...........................39

Command Specification ......................................40

Camera control commands ...............................40
AFE Setting Command .....................................40
DTL/Binarization Setting Command (XCL-5005

only) ................................................................41

Command List ......................................................49
Parameter List ......................................................51
Information ...........................................................52

Specifications

Specifications ........................................................53
Spectral Sensitivity Characteristics (Typical
Values) ...................................................................54
XCL-5005CR/5005 Dimensions ..........................55

Summary of Contents for XCL5005

























































Search results

Summary of Contents for XCL5005

Reviews:

Brands by name

Popular brands

Sony XCL5005, Technical Manual

Search results

Summary of Contents for XCL5005

Reviews:

Brands by name

Popular brands