Sony XCL5005 Technical Manual Download Page 48

Page: 48 / 56

Camer

Con

Command

Command Specification

Others

Version Indication

[Command] VERSION
[Process] The camera model name and the camera

version are displayed.

<Input>

VERSION<CR>

(When XCL-5005)

XCL-5005 Ver.

(When XCL-5005CR)

XCL-5005CR Ver.

<CRLF>

OK<CRLF>

Help Indication

[Command] HELP
[Process] The list of camera control commands is

displayed.

Command Limitation

Even a valid parameter can be invalid in combination
with some settings. In this case, the command is invalid
and “ERROR STATUS” is displayed.

Shutter speed condition

Calculate the partial arbitrary setting by adding the
partial offset value and the line number.

Filter mode (Mode 1 only)

Partial scan mode

One push white balance and manual RGB gain

Trigger mode and pulse polarity

Image output data tap (2TAP only)

Partial scan read area

Shutter speed
setting

Divided
into 16

Divided
into 32

Arbitrary
setting

Pre-setting

0 to 5

0 to 11

1 to 781

1/100 to 1/10000

6 to 15

12 to 31

782 to 2050

1/30 to 1/10000

AUTO-DCLAMP

Filter mode 1

Black balance

0 (OFF)

Setting is
possible.

1 (ON)

Setting is not
possible.

Setting is possible
(left/right
adjustment is not
possible).

BINNING

Partial scan mode

0 (OFF)

Setting is possible.

1 (ON)

Setting is not possible.

WBMODE

PARTIAL

AUTOWB

Manual
RGB gain

0 (3200 K)
1 (5600 K)
2 (6500 K)

0 to 5

Setting is
possible.

Setting is
not possible.

3 (Manual)

0 (OFF)

Setting is
possible.

1 to 5 (ON)

Setting is
not possible.

Setting is
possible.

Shutter speed
setting

Trigger mode

Pulse polarity

0 to 14

Setting is
possible.

Setting is not
possible.

Image output data width

Image output data tap
(2TAP)

0 to 2

Setting is possible.

Setting is not possible.

Summary of Contents for XCL5005

























































Search results

Summary of Contents for XCL5005

Reviews:

Brands by name

Popular brands

Sony XCL5005, Technical Manual

Search results

Summary of Contents for XCL5005

Reviews:

Brands by name

Popular brands