manualshive.com logo in svg

Sony XCL5005, Technical Manual

Share
Download
Sony XCL5005 Technical Manual Download Page 44

Camer

a

 Con

tr

o

l 

Command

s

Command Specification

44

[Parameter 1] <IN data (0 - 4095)>
[Parameter 2] <OUT data (0 - 4095)>
[Process] Sets the LUT value optionally.

x

 LUT Value Setting (the case of gamma mode 

2 and 4)

[Command] GAMMA
[Parameter 1] <Changing point (256 / 512 / 1024 / 

2048 / 3072)>

[Parameter 2] <Strong and weak (1 - 5)>
[Process] Sets the LUT value at the 5 approximation 

points.

x

 LUT Value Setting (When gamma modes 6 

and 7)

[Command] GAMMA
[Parameter 1] <Gamma value (0.00 - 1.00)>
([Parameter 2]) <Gamma offset value (0 - 4095)>
[Process] Sets the LUT value with a gamma value.

Filter Setting Command (XCL-5005 
only)

x

 Filter Mode Setting

[Command] FILTER-MODE
[Parameter 1] <Mode (0 - 2)>

0: OFF
1: Optional setting
2: Table setting

[Process] Sets the filter mode.

x

 Filter Setting (the case of filter mode 1)

[Command] FILTER
[Parameter 1] <Address (11 / 12 / 13 / 21 / 22 / 23 / 31 / 

32 / 33)>

[Parameter 2] <Filter factor (± 0.000 – ±10.000)>
[Process] Sets the filter optionally.

x

 Filter Setting (the case of filter mode 2)

[Command] FILTER
[Parameter 1] <Table pattern (1 - 6)>
[Process] Sets the filter table pattern.

Binning / Partial Setting Command

x

 Binning Mode Setting (XCL-5005 only)

[Command] BINNING
[Parameter 1] <Mode (0 - 1)>

0: OFF
1: ON

[Process] Sets the binning mode.

x

 Partial Scan Setting

[Command] PARTIAL
[Parameter 1] <Mode (0 - 5)>

0: OFF
1: Divided into 16 (XCL-5000 compatible)

2: Divided into 32 (XCL-5000 compatible)
3: Divided into 16
4: Divided into 32
5: Divided into arbitrary number

(When divided into 16)

([Parameter 2]) <Read beginning point (0 - 15)>
([Parameter 3]) <Read block number (0 - 15)>

(When divided into 32)

([Parameter 2]) <Read beginning point (0 - 31)>
([Parameter 3]) <Read block number (0 - 31)>

(When divided into arbitrary number)

([Parameter 2]) <Read beginning point (0 - 408)>
([Parameter 3]) <Read line number (1 - 2050)>

[Process] Specifies the mode setting of partial scan with 

Parameter 1, and the read area for when scan 
operation with Parameter 2 and Parameter 3.
The range of setting values is as follows. Any other 
value is invalid.
The XCL-5005CR sets an even value to Parameter 2 
by placing a primary color filter.
(When divided into 16)

| Read beginning po read line number | 

≤

15

(When divided into 32) 

| Read beginning po read line number | 

≤

31

(When divided into arbitrary number) 

| Read beginning position × 5 + read line number | 

≤

2050

x

 Partial Scan Offset Setting

[Command] PARTIAL-OFFSET
[Parameter 1] <Offset value (0 - 51)>
[Process] Sets offset for partial scan read beginning 

position.
When the partial scan setting is set to Modes 1 to 4 
(divided into 16 or 32), the setting range for the offset 
value (Parameter 1) is 0 to 38.
The XCL-5005CR sets an even value for the offset 
value (Parameter 1) by placing a primary color filter.

x

 Horizontal Partial Scan Setting

[Command] HPARTIAL
[Parameter 1] <Mode (0 - 1)>

0: OFF
1: ON

[Parameter 2] <Read column number (128 - 2448)>
[Process] Sets the read column number for when 

horizontal partial scan operation.
Set the read column number (Parameter 2) to a 
multiple of 4 between the range of 128 to 2448.

IN/OUT Setting Command

x

 External Trigger Signal Input Selection

[Command] EXTTRG
[Parameter 1] <Input specification (0 - 1)>

0: Camera Link

t

DIGITAL IF connector

1: DC

t

DC IN connector

Summary of Contents for XCL5005

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands