manualshive.com logo in svg

Sony XCL5005, Technical Manual

Share
Download
Sony XCL5005 Technical Manual Download Page 41

Camer

a

 Con

tr

o

l 

Command

s

Command Specification

41

x

 Shutter Speed Setting

[Command] SHUTTER
[Parameter 1] <Shutter setting (0 - 15)>

0: OFF

6: 1/500 s

12: 1/2 s

1: 1/15 s

7: 1/1000 s

13: 1 s

2: 1/30 s

8: 1/2000 s

14: 2 s

3: 1/100 s

9: 1/5000 s

15: Arbitrary setting

4: 1/120 s

10: 1/10000 s

5: 1/250 s

11: 1/7.5 s

([Parameter 2]) <Shutter speed adjusting value (0 - 
60000000)>
([Parameter 3]) <Shutter speed fine adjusting (0 - 59)>
[Process] Sets the shutter speed.

If Parameter 1 is set to arbitrary setting, Parameter 
2 and Parameter 3 are valid. 
(When minimum) | Speed adjusting value (0) + 
Speed fine adjusting (3) |
(When maximum) | Speed adjusting value 
(60000000) + Speed fine adjusting (0) |

x

 Trigger Mode Setting

[Command] TRG-MODE
[Parameter 1] <Mode (0 - 2)>

0: OFF

t

Normal output of moving picture

1: External trigger/Edge detection

t

Controls the shutter speed beginning 
exposure from the valid edge of the external 
trigger.

2: External trigger/Pulse width detection

t

Controls the shutter speed with the valid 
pulse width of the external trigger.

[Process] Sets the trigger operation mode.

x

 External Trigger Pulse Polarity Setting

[Command] TRG-POL
[Parameter 1] <Mode (0 - 1)>

0: Negative
1: Positive

[Process] Specifies the polarity of the external trigger 

pulse.

x

 External Trigger Overlap Setting

[Command] TRG-OVLP
[Parameter 1] <Mode (0 - 1)>

0: OFF
1: ON

[Process] Sets the external trigger overlap.

DTL/Binarization Setting Command 
(XCL-5005 only)

x

 Edge Enhancement Filter Factor Setting

[Command] DTL-COEF
[Parameter 1] <Mode (0 - 15)>
[Process] Sets the edge enhancement filter factor.

x

 DTL Mode Setting

[Command] DTL-MODE
[Parameter 1] <Mode (0 - 2)>

0: OFF
1: Edge detection filter
2: Edge enhancement filter

[Process] Sets the DTL mode. Regarding the edge 

enhancement filter, the edge enhancement filter 
factor is reflected.

x

 Binarization Threshold Value Setting

[Command] BINARIZE
[Parameter 1] <Mode (0 - 1)>

0: OFF
1: ON

([Parameter 2]) <Binarization threshold value (240 - 

3900)>

[Process] Sets the binarization mode and the 

binarization threshold value.

WB Setting Command 
(XCL-5005CR only)

x

 White Balance Mode Setting

[Command] WBMODE
[Parameter 1] <Mode (0 - 3)>

0: 3200 K preset

t

The adjustment data of “WB preset value 
adjusting (3200 K)” becomes valid. 

1: 5600 K preset

t

The adjustment data of “WB preset value 
adjusting (5600 K)” becomes valid. 

2: 6500 K preset

t

The adjustment data of “WB preset value 
adjusting (6500 K)” becomes valid. 

3: Manual setting

t

The manual RGB gain setting value becomes 
valid.

[Process] Sets the white balance mode.

x

 One Push White Balance Execution

[Command] AUTOWB
[Parameter 1] <Mode (0 - 1)>

0: Default area
1: Arbitrary area

([Parameter 2]) <Horizontal position (0 - 2192)>
([Parameter 3]) <Vertical position (1 - 1793)>
[Process] Selects the measurement area of one push 

white balance from the default area or an arbitrary 
area.
If Parameter 1 is set to arbitrary area, Parameter 2 
and Parameter 3 are valid. Specify an even number 
between 0 and 2192 for the horizontal position 
(Parameter 2). Specify an odd number between 1 and 
1793 for the vertical position (Parameter 3).
Another command cannot be accepted during the 
execution of one push white balance, and one of the 
following messages appears after processing 
finishes. 

Summary of Contents for XCL5005

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands