manualshive.com logo in svg

Sony XCL5005, Technical Manual

Share
Download
Sony XCL5005 Technical Manual Download Page 18

F

u

nc
ti

ons

4. Camera mode

18

4.2.3.

Partial scan mode

This mode increases the frame rate by dividing the 
whole video period vertically, reading only the 
necessary lines as the actual video, and transferring 
unnecessary lines at high-speed. Set the read beginning 
position (block number PSAH for high-speed 
transferring) and read block number (normal 
transferring block number or line number PSAF).
There are five types of partial scan mode.
In Modes 1 to 4 divide the actual video vertically into 
any of approximately 16 or approximately 32 areas and 
then reads them as the actual video. Mode 5 improves 
the flexibility of area selection and allows for much 
more detailed area settings to be configured.

Line number of actual video

For each of Mode 1 and Mode 3, Mode 2 and Mode 4, 
the division numbers of approximately 16 and 
approximately 32 are the same, but the beginning 
positions of the actual video are different. Mode 1 and 
Mode 2 are the same as the division settings on the XCL-
5000, but they cannot be selected on the XCL-5005CR. 
Mode 3 and Mode 4 have common settings for the XCL-
5005 and XCL-5005CR. Mode 5 allows for detailed 
setting of the actual video lines. 

Partial scan offset

You can use partial scan offset (PARTIAL-OFFSET) to 
offset the beginning position of the actual video output 
in the normal transferring period in increments of 1 line. 
To make the beginning position of the actual video 
output the same as any that of any mode other than 
partial scan, set PARTIAL-OFFSET=0. 

To use Mode 1 of XCL-5005 with the same setting as 
XCL-5000, set PARTIAL-OFFSET=38. The setting is 
PARTIAL-OFFSET=38 at the time of shipment. 

The setting range available for PARTIAL-OFFSET may 
be different depending on the mode.

Beginning and ending position of the actual 
video

In Modes 1 to 4, when the ending position of the actual 
video is set by selecting a certain area and then a 
different setting is configured so that the corresponding 
point becomes the beginning point, both points may not 
match. This is because the high-speed transferring 
period cannot be partitioned in increments of 64 lines. 
You can, however, make both points match if you use a 
partial scan offset. 

Mode

XCL-5005

XCL-5005CR

PSAF

Line number of actual video

1

a

 

–

0 - 15

128 × (PSAF+1)

2

a

 

–

0 - 31

64 × (PSAF+1)

3

a

 

a

 

0 - 15

128 × (PSAF+1)

4

a

 

a

 

0 - 31

64 × (PSAF+1)

5

a

 

a

 

1 - 2050

PSAF

High-speed transferring period

High-speed transferring period

High-speed transferring block number
(High-speed transferring period PSAH)

Modes 1 to 4 : Normal transferring block number
Mode 5

: Normal transferring line number

(Normal transferring period PSAF)

Whole 
area

Normal transferring period

(Effective video output)

PARTIAL-
OFFSET

Mode

Setting range (fixed 
value)

XCL-5000

–

1, 2

(38)

XCL-5005

a

 

1 to 4

Integer from 0 to 38

5

Integer from 0 to 51

XCL-
5005CR

a

 

1 to 4

Even value from 0 to 38

5

Even value from 0 to 50

Summary of Contents for XCL5005

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands