manualshive.com logo in svg

Sony XCL5005, Technical Manual

Share
Download
Sony XCL5005 Technical Manual Download Page 6

Ov
e

rvi

ew

Connection

6

Connection

C-mount lens

Tripod adaptor
VCT-ST70I

Camera cable
CCXC-12P02N
CCXC-12P05N
CCXC-12P10N
CCXC-12P25N

Camera adaptorDC-700/700CE
(Conforms to EIAJ 12-pin assignments)

AC

TRIG

Digital interface cable

Camera module interface board

XCL-5005CR/5005

Power supply

 

You can supply power to the XCL-5005CR/5005 using the following methods.

Using the DIGITAL IF (interface) connector

 

The XCL-5005CR/5005 supports the PoCL (Power over Camera Link) standard. By connecting a PoCL-compatible camera link cable to 
a PoCL-compatible camera module interface board, you can power, control, and output images from the camera using a single cable.

Using the DC IN connector

 

You can supply power via the DC IN connector using the power adapter.
Use DC-700/700CE which is the stable power source free from ripple or noise.
When both the DIGITAL IF and DC IN connectors are used, the power supply from the DC IN connector is given priority.

*

If the camera module interface board for the camera supports PoCL, the 
camera can be operated even if the items within the dashed line are not 
connected.

Summary of Contents for XCL5005

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands