Sony MSB-2000 Operation Manual Download Page 62

Page: 62 / 113

List of Menus

•In asi_to_sdti-cp mode

Item number

Category

Item

Arguments

Function

C013

setup

video_rate

30, 35, 40, 45, 50

The video ES bit rate can be specified in
units of 5 Mbps.
The rate control method is All intra CBG
(IMX).
Unit: Mbps

C015

setup

history

off

Invalidates history insertion into video ES.

part

Validates partial history insertion into video
ES.

full

Validates entire history insertion into video
ES.

C051

setup

rx_audio_sg

off

Disables the internal test signal generator.

1 kHz

Enables the internal test signal generator
to output a 1 kHz sine wave.

silence

Enables the internal terÙ(signal generator
to output silence.

C052

setup

lip_sync

–20.000 to +00.000 to

Carries out lip sync fine adjustment.

+20.000

Unit: ms

Note

When set to a negative value, note that
operation may not be guaranteed,
depending on the system status.

C081

setup

fec_mode

off

Invalidates SDTI-CP FEC.

Validates SDTI-CP FEC.

C101

setup

rx_program_no

00001 to 00200 to 65535 Specifies program number for decoding.

C102

setup

rx_packet_size

auto

Automatically recognizes input TS packet
size.

188

Sets input TS packet size to fixed 188 bytes.

204

Sets input TS packet size to fixed 204 bytes.

C141

setup

rx_udata1

off

Disables user data 1 output from the UDP
port, via the MSBA-20IP.

Enables user data 1 output from the UDP
port, via the MSBA-20IP.

C142

setup

dst_udata1_port

05000 to 09000 to 65535 Set the UDP port No. for outputting user

data 1 from the MSBA-20IP.

C143

setup

dst_udata1_ip

000 to 192 to 255.

Sets the destination IP address for output

000 to 168 to 255.

of user data1 from the MSBA-20IP.

000 to 001 to 255.

000 to 003 to 255

C144

setup

rx_udata2

off

Disables user data 2 output from the UDP
port, via the MSBA-20IP.

Enables user data 2 output from the UDP
port, via the MSBA-20IP.

C145

setup

dst_udata2_port

05000 to 09001 to 65535 Sets the UDP port No. for outputting user

data 2 from the MSBA-20IP.

C146

setup

dst_udata2_ip

000 to 192 to 255.

Sets the destination IP address for

000 to 168 to 255.

outputting user data 2 from the MSBA-

000 to 001 to 255.

20IP.

000 to 003 to 255

Summary of Contents for MSB-2000


















































































































Search results

Summary of Contents for MSB-2000

Reviews:

Brands by name

Popular brands

Sony MSB-2000, Operation Manual

Search results

Summary of Contents for MSB-2000

Reviews:

Brands by name

Popular brands