Sony MSB-2000 Page 72 Operation Manual Download

Page: 72 / 113

List of Menus

L:network menu

This menu is used to make settings for the Ethernet
interface of the MSB-2000 and the Ethernet option
board (MSBA-20IP).

Item number

Category

Item

Arguments

Function

L001

network

ip_addr

000 to 192 to 255.

Specifies the IP address of the MSB-2000.

000 to 168 to 255.

000 to 001 to 255.

000 to 002 to 255

L002

network

netmask

000 to 255 .

Specifies the net mask of the MSB-2000.

000 to 255 .

000 to 255

L003

network

gateway

000 to 255.

Specifies the default gate way of the

000 to 255.

MSB-2000.

000 to 255.

000 to 255

L004

network

mac_addr

–

Display the machine address of the MSB-
2000.

L005

network

ping

000 to 255.

Specifies the destination IP address for

000 to 255.

ping.

000 to 255.

000 to 255

L011

network

opt_ip_addr

000 to 192 to 255.

Specifies the IP address of the MSBA-20IP.

000 to 168 to 255.

000 to 002 to 255.

000 to 002 to 255

L012

network

opt_netmask

000 to 255 .

Specifies the net mask of the MSBA-20IP.

000 to 255 .

000 to 255

L013

network

opt_gateway

000 to 255.

Specifies the default gateway for the

000 to 255.

MSBA-20IP.

000 to 255.

000 to 255

L014

network

opt_mac_addr

–

Displays the machine address of the
MSBA-20IP.

L015

network

phy_mode

100

This is a 100 Mbps full-duplex fixed mode.

auto

This enables auto negotiation. As a result
of negotiation with the other end, the
connection is made at the highest speed
mode.

Note

Be sure to check the device connected at
the other end, and set to the same
communications mode. If not set to the
same communications mode, normal
operation may not be possible.

Summary of Contents for MSB-2000


















































































































Search results

Summary of Contents for MSB-2000

Reviews:

Related manuals for MSB-2000

Brands by name

Popular brands

Sony MSB-2000, Operation Manual

Search results

Summary of Contents for MSB-2000

Reviews:

Related manuals for MSB-2000

Brands by name

Popular brands