Sony MSB-2000 Operation Manual Download Page 70 | Manualshive

Page: 70 / 113

Sony MSB-2000 Operation Manual Download Page 70

70

List of Menus

•

In sdti-cp_to_asi mode

Item number

Category

Item

Arguments

Function

E001

**

link_mng (Tx)

rtp_tx

off

Invalidates MPEG streaming output
through the MSBA-20IP.

on

Validate MPEG streaming output through
the MSBA-20IP. Streaming supports up to
35 Mbps as a TS rate.

E002

**

link_mng (Tx)

rtp_tx_ip

000 to 255.

Sets the destination IP address for MPEG

000 to 255.

streaming output through the MSBA-20IP

.

000 to 255.

For Multicast transmission, select in the

000 to 255

range 224.0.0.0 to 239.255.255.255.

E003

**

link_mng (Tx)

rtp_tx_port

50000 to 65534

Sets the UDP port No. for MPEG
streaming output through the MSBA-20IP.
The port No. can only be set to an even
number. The RTCP port No. is the setting
value plus one.

E004

**

link_mng (Tx)

rtp_tx_ssrc

0x00000000 to

Sets “SSRC” which is member of RTCP.

0x01234567 to 0xffffffff

Default value is 0x01234567.

E005

**

link_mng (Tx)

rtp_tx_fec_mode

off

Invalidates Error collection.

on

Validate Error collection.

E006

**

link_mng (Tx)

rtp_tx_format

1

Selects Streaming packet format.

2

1: 1 TS packet per IPdatagram

2: 6 TS packets per IP datagram

Note

It is recommended to use a setting of “2”
with less overhead. Avoid using both “1”
and “2” on the same network.
The IP transfer bandwidth required for
each TS rate is as follows.
• For a setting of “1” when “C165” is “off”:

141% of TS rate

• For a setting of “1” when “C165” is “on”:

156% of TS rate

• For a setting of “2” when “C165” is “off”:

107% of TS rate

• For a setting of “2” when “C165” is “on”:

122% of TS rate

E007

**

link_mng (Tx)

rtp_tx_cname

MSB-2000

Sets “CNAME” which is member of RTCP.
Default CNAME here is “MSB-2000”.
Maximum length is 15 characters.The
characters that can be used are ASCII
codes in the range 0x21 to 0x7d.

E031

**

link_mng (Tx/Rx)

tos_field

00 to ff

Specifies the value (8 bits) of the Tos field
(Diff serve field) of IP packets output by the
MSBA-20IP.

E998

**

link_mng

cancel

–

Cancels a link_mng change before
execution.

E999

**

link_mng

init

–

Returns link_mng items to their factory
default settings.

–

**

link_mng

list

–

Displays the list set in link_mng.
This is a special-purpose command for
RS232C/telnet operation.

«
...
68
69
70
71
72
...
»

Summary of Contents for MSB-2000


















































































































Reviews:

No comments