Sony MSB-2000 Page 73 Operation Manual Download

Page: 73 / 113

List of Menus

M:setup-msb menu

This menu contains common settings for the MSB-
2000.

Item number

Category

Item

Arguments

Function

M001

setup-msb

video_system

525

Selects video system 525.

625

***

Selects video system 625.

M002

setup-msb

lock-web

unlock

Accepts control from from the web.

lock

Inhibits control from the web.

Note

Even when control is disabled, this can be
unlocked through the web.

M003

setup-msb

lock-telnet

unlock

Accepts control from telnet.

lock

Inhibits control from telnet.

Note

Even when control is disabled, this can be
unlocked through telnet.

M004

setup-msb

lock-snmp

unlock

Accepts control from snmp.

lock

Inhibits control from snmp.

Note

Even when control is disabled, this can be
unlocked through snmp.

M008

setup-msb

remote1

off

Disables VTR remote 1.

VTR

Enables VTR remote 1.

M009

setup-msb

remote2

off

Disables VTR remote 2.

VTR

Enables VTR remote 2.

M010

setup-msb

date

[yymmdd]hhmm

Sets the date and time.

M011

setup-msb

lcd_cont

1 to 12 to 20

(not on help) Sets the LCD contrast.

M012

setup-msb

lcd_bright

1 to 9 to 20

(not on help) Sets the LCD brightness.

M013

setup-msb

serial_no

–

Displays the serial number of the MSB-2000.

M014

setup-msb

opt_serial_no

–

Displays the serial number of the MSBA-
20IP.

–

setup-msb

parameter_list

–

Displays all the currently set parameters.
This is a special-purpose command for
RS232C/telnet operation.

–

setup-msb

parameter_file

–

Creates a parameter file named
“PARAMS.”
This is a special-purpose command for
RS232C/telnet operation.

–

setup-msb

parameter_load

–

Loads a parameter file named “PARAMS.”
This is a special-purpose command for
RS232C/telnet operation.

–

setup-msb

list

–

Displays the list set for setup-msb.
This is a special-purpose command for
RS232C/telnet operation.

Note

The parameter file holds the values of all settings
in the B, C, E, L, M, N, S, and U menus and
SNMP menu.

For details of the parameter file, refer to the
Maintenance Manual.

Summary of Contents for MSB-2000


















































































































Search results

Summary of Contents for MSB-2000

Reviews:

Related manuals for MSB-2000

Brands by name

Popular brands

Sony MSB-2000, Operation Manual

Search results

Summary of Contents for MSB-2000

Reviews:

Related manuals for MSB-2000

Brands by name

Popular brands