9
Names and Functions of Parts
qa
Cursor keys (
vVbB
)
In the menu display, press the
v
and
V
keys to select
an item.
In the menu display, press the
b
and
B
keys to move
through the menu levels.
When a setting value is an IP address or other value
that you enter directly, use the
b
and
B
keys to select
a digit, and the
v
and
V
keys to change the numeric
value.
The
v
,
V
,
b
and
B
keys have an auto-repeat mode
when held down.
When menu operations are enabled on the monitor
screen, press the
v
and
V
keys to select a submenu.
Press the
b
and
B
keys to select an input program.
qs
RESET button
This resets the unit. Use a sharp object to press the
recessed button.
Rear panel
1
REF IN (reference input) connector (BNC type)
Input a reference video signal from an external device.
Note
To this connector, connect a signal such as black burst
whose amplitude does not fluctuate.
2
INPUT connectors
SDI/SDTI (serial digital interface/serial data
transport interface input) connectors (BNC
type): The left connector is an input connector for
SDI/SDTI-CP format digital video/audio signals.
The right connector is an active through output,
which while the unit is powered on outputs a
wave-shaped copy of the signal input to the left
connector.
BIT STREAM DVB ASI connector (BNC type):
This is an MPEG2 serial bit stream input
connector. This allows DVB serial (DVB-ASI
standard compliant (DVB A010 compliant))
format transport input.
BIT STREAM MON OUT (bit stream monitor
output) connector (BNC type): While the unit is
powered on, a wave-shaped copy of the signal
input to the BIT STREAM DVB ASI connector is
output.
CASCADE DVB ASI connector (BNC type): Not
currently used.
3
OUTPUT connectors
SDI/SDTI (serial digital interface/serial data
transport interface output) 1, 2 connectors
(BNC type): These output SDTI-CP format
digital video/audio signals.
SDI MON (serial digital interface monitor output)
(SUPER) connector (BNC type): This outputs an
SDI signal for a monitor.
The on-screen display can be enabled by a menu
setting. For more details, see “On-Screen Display
Overview” (page 16) and “List of Menus” (page 36).
Notes
• If the menu item “C021” is set to “LPCM” and
“C026” to “1-8” when “sdi_to_asi” or “sdti-
cp_to_asi” is selected in the “B:mode” menu,
then no audio is output from the SDI/SDTI and
SDI MON (SUPER) connectors.
• If the menu item “C004:monitor_select” is set to
“tx” when “tx-rx” is selected in the “B:mode”
menu, then no audio is output from the SDI
MON (SUPER) connector.
• If “tx-rx (cm)” is selected in the “B:mode” menu,
neither video nor audio is output from the SDI
MON (SUPER) connector.
• The SDI MON (SUPER) connector does not
support EDH or VBI transmission. Depending on
the mode, it does not support video/audio output,
as described above.
BIT STREAM DVB ASI 1, 2 connectors (BNC
type): These are MPEG2 serial bit stream output
connectors. This allows DVB serial (DVB-ASI
standard compliant (DVB A010 compliant))
format transport output.
4
CONTROL I/O (control input/output)
connectors
REMOTE1 connector/REMOTE2 connector (D-
sub 9-pin, RS-422A standard compliant,
female): Connect to the REMOTE connector of
an MSW-M2000/A2000/2000, Betacam VTR, or
similar, to enable remote control of the VTR.
For more details, see “Changing Settings Using a Web
Browser” (page 29).
Note
The maximum guaranteed cable length for the
REMOTE1/REMOTE2 connector is 200 m.
1) Ethernet is a registered trademark of Xerox Corporation.
.........................................................................................................................................................................................................
