Sony IFB-LE100, Service Manual

Page: 41 / 258

1-35
VPD-LE100A/LE100E/LE100U
24
Connection Examples
0 0
CONTOROL S
IN
PLIG IN POWER
STATUS/ERROR MESSAGE
OUT
STANDBY
1
ON
@
RS-
232C
RS-
422A
RS-232C/422A PJ COM IN
R G/G SYNC SYNC/HD VD B
OUT
TRIG DEVICE INDEX CONTOROL
0 0
CONTOROL S
IN
PLIG IN POWER
STATUS/ERROR MESSAGE
OUT
STANDBY
1
ON
@
RS-
232C
RS-
422A
RS-232C/422A PJ COM IN OUT
TRIG DEVICE INDEX CONTOROL
STATUS/ERROR MESSAGE
IN PLIG IN POWER OUT RS- 232C RS- 422A RS-232C/422A PJ COM IN OUT
STANDBY
1
ON
@
0 0
CONTOROL S TRIG DEVICE INDEX CONTOROL
STATUS/ERROR MESSAGE
IN PLIG IN POWER OUT RS- 232C RS- 422A RS-232C/422A PJ COM IN OUT
STANDBY
1
ON
@
0 0
CONTOROL S TRIG DEVICE INDEX CONTOROL
1
2 3 4
5
8 6
7
SW NO.
1
2 3 4
5
8 6
7
SW NO.
OUT PUT
SW NO
SW NO
OUT PUT
RS-232C/422A
REMOTE
RS-485 IN
RS-485 OUT
RS-232C
RS-422A
RS-232C/422A
REMOTE
RS-232C
RS-422A RS-485 IN
RS-485 OUT
:
When using the switcher
When connecting two PC-3000 switchers, up to 15
inputs can be selected as the input from the switchers.
Install the IFB-12A interface board in the first switcher
(on which you set the SW NO switch to 1) and set the
IN/OUT switch on the board to IN.
Notes
• Be sure to set the switcher number.
• Be sure to turn off the power of the projector when
setting up the device index number and connecting
cables.
Attach the
supplied
terminator.
SIC-10 connecting cable
(5BNC
y 5BNC)
(not supplied)
RCC-5G/10G/30G connecting
cable (not supplied)
IFB-12A
IN/OUT switch:
OUT
to OUTPUT
to PJ COM
OUT
PC-3000 switcher
SW NO switch: 1
to PJ COM IN to IFB-12A
installed in
the switcher
PC-3000 switcher
SW NO switch: 2
Computer
IFB-12A
IN/OUT switch: IN
Computer
Signal flow
AC power cord
(supplied)
to PJ COM OUT
to OUTPUT
Rear
Attach the
terminator (supplied
with the PC-3000).
Set to 2.
Set to 1.
to INPUT A
to PJ COM IN
Device index
number: 01
to PJ COM OUT
to PJ COM
IN
to INPUT A
Device index
number: 02
to IFB-12 A installed
in INPUT B
Rear
AC power cord
(supplied)
to a wall outlet
(200-240 V AC,
15 A or more)
to a wall outlet
(200-240 V AC,
15 A or more)
to AC inlet (front)
to AC inlet (front)
25
Connection Examples
Confirming the System
Construction
After all the connections are complete, confirm that
equipment of the system is properly setup.
1
Connect the AC cords of all equipment to the AC
outlets and turn the power on.
Set the POWER switch of this projector to ON.
2
Press the SYS SET key.
Information on the system construction and the
settings of the interface boards, etc. are
automatically confirmed. Then the message
disappears.
Note
When you want to use the projector without
connecting the switcher after using the switcher in the
system connections, it is necessary to confirm the
system construction again by pressing the SYS SET
key after all the connections are complete. If you press
the key(s), “Master Switcher not exist” appears, but
the system construction is automatically recognized.
Remedy
Set the switcher that outputs
the signal to the projector to
number 1.
Change either number of the
projectors that have the same
number.
Change either number of the
switchers that have the same
number.
When a system error is detected
The following messages are displayed on the screen
and the message display window on the rear of the
projector:
Message
Master Switcher not exist.
Same DEVICE INDEX for
Projector detected.
Same DEVICE INDEX for
Switcher detected.
Note
If the projector is in standby mode, the message in
English appears only in the message display window.