Sony IFB-LE100, Service Manual, Page: 36 / 258

1-30
VPD-LE100A/LE100E/LE100U
14
Location and Function of Controls
ed CONTROL S OUT jack
Connect the supplied remote commander cable to this
jack and to the CONTROL S IN jack of the projector
for wired remote control operation.
When the Commander is connected to the CONTROL
S IN/PLUG IN POWER jack of the projector via the
remote commander cable (stereo), the power for the
Remote Commander is supplied from the projector.
Battery installation
1
Push to open the lid, and install three R6 (size AA)
batteries (supplied) with the polarities correctly
aligned.
2
Replace the lid.
Notes on batteries
• Make sure that the battery orientation is correct when
inserting batteries.
• Do not mix old battery with new one, or different
types of batteries.
• If you will not use the Remote Commander for a long
time, remove the batteries to avoid damage from
battery leakage. If batteries have leaked, remove
them, wipe the battery compartment dry and replace
the batteries with new ones.
Be sure to install the battery
from the
# side.
ql ADJ R/G/B keys
Select the color to be adjusted when adjusting the
white balance.
w; REGISTRATION keys
These keys do not function with this projector.
wa W/B (white balance) keys
Enter the white balance adjustment mode.
BIAS: Adjusts cut off.
GAIN: Adjusts drive.
ws PO/– keys
These keys do not function with this projector.
wd FOCUS LENS key
Functions the same as the LCD LENS CONTROL
FOCUS key.
wf MG FOCUS key
The key does not function with this projector.
wg VOL (volume) +/– keys
These keys do not function with this projector.
wh PICTURE C/– keys
Adjust the picture conditions: CONTR (contrast),
BRIGHT (brightness), COLOR, HUE and SHARP
(sharpness).
wj PO/– keys
These keys do not function with this projector.
wk RESET key
Resets the adjusted value of an item to its factory
preset value. This key functions when the menu or a
setting item is displayed on the screen.
wl FUNCTION key
The key does not function with this projector.
e; ENTER key
Stores the settings in the menu.
ea Arrow and +/– keys ( M / m / < / , /+/–)
Used to adjust the picture after pressing the LENS
CONTROL or RGB key. Also used to move the cursor
or adjust the value in the menu.
es MENU key
Displays the menu on the screen.
Press again to turn off the menu.
15
Location and Function of Controls
0 0
CONTOROL S
IN
PLIG IN POWER
STATUS/ERROR MESSAGE
OUT
STANDBY
1
ON
@
RS-
232C
RS-
422A
RS-232C/422A PJ COM IN
R G/G SYNC SYNC/HD VD B
OUT
TRIG DEVICE INDEX CONTOROL
To connect the Remote Commander to the
projector
Note on wired Remote Commander operation
using the supplied remote commander cable
(stereo)
You do not need to install the batteries since the power
is supplied from the CONTROL S IN jack on the
projector. In this case, the batteries are not consumed.
Notes on wireless Remote Commander
operation
• Be sure that there is nothing to obstruct the infrared
beam between the Remote Commander and the
projector.
• The operation range is limited. The shorter the
distance between the Remote Commander and the
projector, the wider the angle within which the
commander can control the projector.
• The remote control detectors on the projector do not
operate when connecting the remote commander
cable to the CONTROL S IN jack. If you wish to use
the Remote Commander as a wireless Remote
Commander, be sure to remove the remote
commander cable from both the Remote Commander
and the projector.
To open the cover of the service
adjustment keys
When using the service adjustment keys qk to wf ,
open the cover as follows:
Note
The service adjustment keys qk to wf operate only
when the projector is in the service mode.
For entering the service mode, see page 37.
Slide the cover while
pushing it.
Lift the cover
slightly to open.
Rear
Remote
commander
cable (supplied)
Remote Commander
to CONTROL S OUT
to CONTROL
S IN