14
Copyright© 2017 SOMFY ACTIVITES SA. All rights reserved.
Axovia 220B RTS
DE
12.1. Anschluss an die Stromversorgung
Schließen Sie das Solarstrom-Versorgungskabel an die Klemme "BATT"
des elektronischen Steuergeräts des Antriebs an.
Ant
.
BU
S
Ce
ll
24Vd
c
13
5
7
9
11
24
6
8
10
12
Fl
as
h
M1
M2
B
a
tt.
MM
+
-
+
-
13
15
14
16
L
a
mp
230V
ac
+
-
1
2
3
+
-
2
1
3
12.2. Hinweise zur Benutzung
Bei einem Tor mit Stabfüllung empfiehlt es sich, alle in Armhöhe zugäng-
lichen Bereiche von außen vor Eingriff zu schützen.
Zur Reduzierung des Energieverbrauchs Ihrer Toranlage, empfiehlt es sich:
• das Tor stets zu schließen, um die Batterieaufladung zu optimieren,
• das Tor nicht länger als 2 Tage offen zu lassen,
• die automatische Schließfunktion des Tors zu aktivieren.
13.
DIAGNOSE UND STÖRUNGSBESEITIGUNG
Achtung
Trennen Sie die Anlage bei Reinigungs- oder Instandsetzungsarbei-
ten stets von der Hauptstromversorgung.
DIAGNOSE
STÖRUNGSBESEITIGUNG
Die Antriebe
reagieren nicht
auf die Befehle
des Funksen-
ders.
Die Reichweite
des Funksenders
ist einge-
schränkt.
- Prüfen Sie die Batterie des Funk-
handsenders.
- Kontrollieren Sie die Antenne des
elektronischen Steuergeräts.
- Stellen Sie sicher, dass die
Funkwellen nicht durch äußere
Einflüsse gestört werden (Strom-
mast, metallbewehrte Mauern
usw.). Ist dies der Fall, sollten
Sie auch außen eine Antenne
anbringen.
Funkhandsender
nicht program-
miert
Lernen Sie den Funkhandsender
ein.
1 oder 2 Antriebe
sind entriegelt
Verriegeln Sie die Antriebe.
Die LED
=
=
des elektro-
nischen Steuer-
geräts leuchtet
nicht
Motor wird ohne
Stromversor-
gung
- Prüfen Sie die Stromversorgung.
- Prüfen Sie das Stromversor-
gungskabel.
Außen ist zu
wenig Licht
= Antrieb im
Standby-Modus.
Sorgen Sie für mehr Helligkeit
im Bereich des elektronischen
Steuergerätes (zum Beispiel mit
einer Taschenlampe) und nehmen
Sie dann die Einstellungen vor
(siehe Umgebungslichtssensor
weiter unten)
DIAGNOSE
STÖRUNGSBESEITIGUNG
Die LED
=
=
des elektro-
nischen Steuer-
geräts blinkt
1 Impuls
Betrieb mit
Notstrombatterie
Prüfen Sie die Stromversorgung.
2 Impulse
Am Antrieb
wurde der Tor-
weg noch nicht
automatisch
eingelernt
Starten Sie das Einlernen des
Torwegs.
3 Impulse
Störung Foto-
zellen:
- Fotozellen
verdeckt
Beseitigen Sie das Hindernis, das
die Fotozellen verdeckt.
- Fotozellen
sind nicht richtig
ausgerichtet
Korrigieren Sie die Ausrichtung
(siehe mitgelieferte Anleitung der
Fotozellen).
- Falsche
Verkabelung der
Fotozellen
Schließen Sie die Fotozellen unter
Beachtung der Anweisungen an.
- Fotozellen
nicht vorhanden/
nicht ange-
schlossen
- Stellen Sie sicher, dass die Foto-
zellen korrekt angeschlossen sind.
- Wenn Sie die Fotozellen absicht-
lich abgeklemmt haben und Ihr
Tor im Modus automatisches
Schließen funktioniert, müssen
Sie den Modus automatisches
Schließen deaktivieren.
4 Impulse
Kurzschluss am
BUS-Ausgang
(Klemmen 3-4)
des elektroni-
schen Steuer-
geräts
Überprüfen Sie die Zubehörteile,
die am BUS-Ausgang des elektro-
nischen Steuergeräts angeschlos-
sen sind.
5 Impulse
Überhitzungs-
schutz der Elekt-
ronik ausgelöst
Lassen Sie die Elektronik ab-
kühlen, bis die LED
=
=
wieder
ununterbrochen leuchtet.
6 Impulse
Kurzschluss am
24 V-Ausgang
(Klemmen 5-6)
des elektroni-
schen Steuer-
geräts
Überprüfen Sie das Zubehör, das
am 24 V-Ausgang des elektroni-
schen Steuergeräts angeschlossen
ist.
Kurzschluss
an der gelben
Signalleuchte
(Klemmen 7-8)
des Steuerkas-
tens
Überprüfen Sie den Anschluss der
gelben Signalleuchte.
Kurzschluss am
Antrieb
Prüfen Sie die Verdrahtung des
Antriebs.
Der Modus
automatisches
Schließen wird
nicht aktiviert
(LED
bleibt erlo-
schen).
Die Fotozel-
len sind nicht
montiert
Installieren Sie eine Lichtschranke
(Installation siehe die mit den Foto-
zellen gelieferte Anleitung).