Solwise 3G11nMRW User Manual Download Page 33

Page: 33 / 257

Version 1.0.15

4.2.2

LAN Interface Setup

If you are using 3.5G plus 11n Mobile Server Router with multiple PCs on your LAN, you must

connect the LAN via the Ethernet ports on the built -in Ethernet switch. You must assign a

unique IP address to each device residing on your LAN. The LAN IP a ddress identifies the

router as a node on your network; that is, its IP address must be in the same subnet as the

PCs on your LAN. The default LAN IP for the Internet Security Router is 192.168.1.1.

For Gateway IP Address, the IP address 192.168.1.xxx (x xx can be any number between 1

and 254 that is not used by another device.) Please don’t change the default LAN IP settings

at this section until you have completed the rest of the configurations and confirm that your

Internet connection is working.

Click on

Next

button to proceed.

4.2.3

WAN Setup

The WAN settings can be referred to as the Public setting. All IP information in the WAN

settings is public IP addresses which are accessible on the Internet. 3.5G plus 11n Mobile

Server Router supports 3 interfaces and 4 access types to WAN. Select one of the WAN

connection modes required by your ISP in the following WAN Setup Configuration page, the

WAN setup pages will vary depending on what kind of WAN Type you select.

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Solwise 3G11nMRW, User Manual, Page: 33 / 257

Search results

Summary of Contents for 3G11nMRW

Reviews: