Solwise 3G11nMRW User Manual Download Page 249

Page: 249 / 257

Version 1.0.15

249

11n Mobile Server Router. Without DHCP, you would have to configure each

computer separately. It’s very troublesome. Please Open

Internet browser

> Input

192.168.1.1 in the website blank field

> Select

DHCP Server under

the

IP Config

Menu

. For more information, please refer to 3.3.2 (Router Mode) or 4.3.1 (AP Mode).

Q: How do I upgrade the firmware of 3.5G plus 11n Mobile Server Router?

A: Periodically, a new Flash Code is available for 3.5G plus 11n Mobile Server Router

on your product supplier’s website. Ideally, you should update 3.5G plus 11n Mobile

Server Router’s Flash Code using

Firmware Upgrade

on the

System Management

menu of 3.5G plus 11n Mobile Server Router Settings.

Q: My

3.5G plus11n Mobile Server Router

cannot connect to the ISP?

A: There are three possible solutions.

1. Check the Cable/XDSL modem is power on.

2. Check the Cable/XDSL link light is on to verify a good physi cal connection.

3. Check the WAN port LED to verify if the Cable/XDSL modem is connected to the

router:

If your ISP Login method is following, please make sure the username and password

are correct or not.

If your ISP is using dynamic IP addressing (DHCP) t hen the DHCP protocol does not

have the authentication feature. Some Cable service providers often use the following

to determine user’s identification.

Q: Why is that I can ping to outside hosts, but cannot access Internet websites?

A: Check the DNS server settings on your PC. You should get the DNS servers settings

from your ISP. If your PC is running a DHCP client, remove any DNS IP address

setting. As the router assign the DNS settings to the DHCP -client-enabled PC.

Q: 3.5G plus 11n Mobile Server Router couldn’t save the setting after click on

Apply button?

A: 3.5G plus 11n Mobile Server Router will start to run after the setting finished applying,

but the setting isn’t written into memory. Here we suggest if you want to make sure

the setting would be written into memory, please reboot the device via

Rebo

ot under

System Management

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Solwise 3G11nMRW, User Manual, Page: 249 / 257

Search results

Summary of Contents for 3G11nMRW

Reviews: