manualshive.com logo in svg

Solarflare SFA6902F, User Manual, Page: 265 / 375

Share
Download
Solarflare SFA6902F User Manual Download Page 265

Issue 11

© Solarflare Communications 2014

260

Solarflare Server Adapter

User Guide

TCP/IP Checksum Offload

Checksum offload moves calculation and verification of IP Header, TCP and UDP packet checksums 
to the adapter. The driver by default has all checksum offload features enabled. Therefore, there is 
no opportunity to improve performance from the default. 

Checksum offload is controlled using ethtool: 

Receive Checksum:

# /sbin/ethtool –K <vmnicX> rx <on|off>

Transmit Checksum:

# /sbin/ethtool –K <vmnicX> tx <on|off>

Verification of the checksum settings may be performed by running ethtool with the 

–k

 option. 

Solarflare recommend you do not disable checksum offload.

For advice on configuring checksum offload in the guest, consult the relevant Solarflare section for 
that guest, or the documentation for the guest operating system. 

TCP Segmentation Offload (TSO)

TCP Segmentation offload (TSO) offloads the splitting of outgoing TCP data into packets to the 
adapter. TCP segmentation offload benefits applications using TCP. Non TCP protocol applications 
will not benefit (but will not suffer) from TSO.

Enabling TCP segmentation offload will reduce CPU utilization on the transmit side of a TCP 
connection, and so improve peak throughput, if the CPU is fully utilized. Since TSO has no effect on 
latency, it can be enabled at all times. The driver has TSO enabled by default. Therefore, there is no 
opportunity to improve performance from the default. 

 

TCP Large Receive Offload (LRO)

TCP Large Receive Offload (LRO) is a feature whereby the adapter coalesces multiple packets 
received on a TCP connection into a single call to the operating system TCP Stack. This reduces CPU 
utilization, and so improves peak throughput when the CPU is fully utilized. 

LRO should not be enabled if you are using the host to forward packets from one interface to 
another; for example if the host is performing IP routing or acting as a layer2 bridge. 

LRO is supported, and enabled by default, on VMware versions later than ESX 3.5.

NOTE: 

TSO cannot be controlled via the host on VMware ESX. It can only be controlled via the guest 

Operating System.

Summary of Contents for SFA6902F
























































































































































































































































































































































































Reviews:

No comments