background image

if (from some reason) the module was already opened, manipulate with it very carefully or renew its silicon
filling by pouring of a few milliliters of special silicon (same as original - consult the technique with manu-
facturer).

In case the module has been opened, there is no manufacturer’s guarantee of IP68

degree of protection.

;

install modules only to the sites where they can be dipped into the water only occasionally and only for a
short time;

do not install modules to the sites where their antenna could be submerged under water. Antenna must be
installed to such place, where there is no possibility to be flooded.

Operating of the module with antenna

submerged under water could cause irretrievable damage of the device!

4.1

The condition of modules on delivery

Modules are delivered in standard cardboard boxes. The modules are commonly delivered with battery switched
off. There is an exception in case the modules are delivered with additional sealing by silicon filling - in this case
the modules are switched on.

4.2

Modules storage

It is strongly recommended to store the modules in dry rooms or halls, in the temperature interval (0

÷

30)

C. To prevent the unwanted discharging of internal battery it is recommended storing the modules with batteries

disconnected and activate the battery during mounting (with exception of modules with additional sealing by silicon
filling - see paragraph

4.1

).

4.3

Safety precautions

Warning!

Mechanical and electrical installation of the WB169-SI2 module can be provided only by a person with

necessary qualification in electrical engineering.

4.4

Environmental protection and recycling

The equipment contains non-rechargeable lithium battery. It is necessary to remove battery before module disposal
and dispose battery separately in compliance with the dangerous waste disposal rules. Damaged, destroyed or
discarded devices cannot be disposed as household waste. Equipment must be disposed of in the waste collection
yards, which dispose electronic waste. Information about the nearest collection yard can be provided by the relevant
local (municipal) authority.

4.5

WB169-SI2 module installation

WB169-SI2 radio modules are enclosed in plastic casings with an IP65 degree of protection equipped with mounts
for mounting on the wall, pipe or any other construction element. In the figure

18

there is displayed the WB169-SI2

module dismantled into individual components.

Figure 18: Set of WB169-SI2 module components with stick antenna

WB169-SI2

33

Summary of Contents for WB169-SI2













































Reviews: