Snell & Wilcox HD5050 Operator'S Manual Download Page 10

Page: 10 / 51

HD5050

SECTION 3

HD5050070999 Version 1 Issue 4

For Software Version Z5 onwards

3.1

Installation

UNPACKING THE HD5050

The unit is packed in a single flight case. The
contents of the flight case are as follows:

HD5050 unit
1 Power cable
1 Extender card
2 Spare a.c. power fuses
1 Operating Manual

Unpack the flight case carefully and check for any
shortages or shipping damage. Immediately report
any shortages or damage to Snell and Wilcox
Limited.

POWER CONNECTIONS

Power Supply

Mains power is supplied to the unit via a filtered
IEC connector.

The mains power fuse rating is 4 A (T) and the
rated current for the unit is 2.6 A at 100 V and
1.2 A at 240 V.

The ON/OFF switch is located on the rear panel as
part of the mains inlet assembly

Note that the fan ventilation holes on the rear panel
must not be obscured.

Supply Voltage

The unit automatically senses the supply voltage in
the ranges 85

V to 264

V and sets itself up

accordingly. No voltage adjustment procedure is
required.

Power Connections
The unit is supplied with a power cable that must
be wired into a power plug as follows:-

Brown

Line

Blue

Neutral

Green/Yellow

Earth (ground)

CAUTION THIS UNIT MUST NOT BE

OPERATED WITHOUT

AN EARTH CONNECTION.

Fuse

CURRENT

V / 1.2A 230 V

60/50Hz

FUSE T4A

85-260 V

Summary of Contents for HD5050




















































Search results

Summary of Contents for HD5050

Reviews:

Related manuals for HD5050

Brands by name

Popular brands

Snell & Wilcox HD5050, Operator'S Manual

Search results

Summary of Contents for HD5050

Reviews:

Related manuals for HD5050

Brands by name

Popular brands