manualshive.com logo in svg

Snell & Wilcox HD1012, Installation Manual

Share
Download
Snell & Wilcox HD1012 Installation Manual Download Page 4

www.snellwilcox.com

Page

HD1012 Installation Manual – V3, Issue 1, Rev 1

S&W Production & Post Production

iv

Power cable supplied for the USA

The equipment is shipped with a power cord with a standard IEC molded free socket on one end
and a standard 3-pin plug on the other.  If you are required to remove the molded mains supply
plug, dispose of the plug immediately in a safe manner. The color code for the lead is as follows:

GREEN lead connected to E
(Protective Earth Conductor)
WHITE lead connected to N
(Neutral Conductor)
BLACK lead connected to L
(Live Conductor)

Power cable supplied for countries other than the USA

The equipment is shipped with a power cable with a standard IEC moulded free socket on one end
and a standard IEC moulded plug on the other.  If you are required to remove the moulded mains
supply plug, dispose of the plug immediately and safely. The colour code for the lead is as follows:

GREEN/YELLOW lead connected to E
(Protective Earth Conductor)
BLUE lead connected to N
(Neutral Conductor)
BROWN lead connected to L
(Live Conductor)

Free Socket

Free Plug

Control Panel Power cable tie

A cable tie mount is located by the  power inlet
on the control panel.  A cable tie may be used
to fix the power cable to the unit to prevent
accidental disconnection of power.

If this facility is used allow enough cable after
the tie to allow the power plug to be easily
removed from and inserted into the power
socket.

Min length after tie = 20mm

Cable tie

mount

Cable tie

I O

Battery Warnings

Lithium Battery - 

There is a Lithium battery on the VME card which is mounted “piggy-back” on
the Mainframe CPU card.

If this battery is incorrectly replaced there is a danger of explosion!

Ensure that the same make and model of battery is used if replacement is
required (a manufacturer recommended equivalent may be used if the original
type is not available).

Empty Holder

-

There is an empty battery holder on the MBX card in the Control Panel, this
holder is not used.

No battery should be fitted to this card!

Summary of Contents for HD1012


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands