Smiths Kelvin Hughes Nucleus 3 5000 Series, System Handbook

Page: 465 / 510

OP ER ATING IN STRUC TIONS
53 The Flat Panel Display is used in conjunction with a
Remote Trackerball and an ON/OFF Sounder. The
following paragraphs provide information on operating and
provide descriptions of the controls and indicators provided
on the Flat Panel Displays and on the associated Remote
Trackerball unit and ON/OFF Switch unit.
OP ER ATING
54
The Operation of the Nucleus 3 System, fitted with Flat
Panel Displays is identical to that of a system using the
5000 and 6000 series displays. Refer to Chapter 1, for
operating information.
POWER ON/OFF
55
The Display is switched ON using the ON/OFF switch,
located on the front of the display unit.
56 The Radar System is switched ON using the ON/OFF
switch on the ON/OFF Sounder Unit (NNR-A65).
57
It is recommended that the Display ON/OFF switch is
set to the ON position and remains in the ON position,
and that the system is switched ON/OFF at the ON/OFF
Sounder Unit. This avoids confusion over whether the Radar
system is on or off when the Display is switched OFF.
CON TROLS AND IN DI CA TORS
20-inch Flat Panel Dis play
58
The 20-inch Flat Panel Display is fitted with the
following controls and indicators:
(1) Display POWER ON/OFF switch, located on the
front panel of the unit.
(2) BRIGHTNESS control, located on the front panel.
(3) CONTRAST control, located on the front panel.
(4) POWER (Green) LED - indicates Power ON.
On-Screen Ad just ment Con trols
59 The Display can be adjusted using an On-screen
Display (OSD) and the following pushbutton controls:
(1) SELECT - enables the Parameter menu to be
opened.
(2) EXIT - allows exit from menu selections.
(3) Adjust (+ and - keys) - used to select a parameter
and to make adjustments once a parameter is
selected.
60
For the best picture setting, a suitable test image of the
required resolution should be used. Set up the monitor
as follows:
(1) Press the SELECT key to open the required
parameter.
(2) Open the required sub-menu/parameter, by
pressing SELECT, then using the ADJUST [+] and
[-] keys make the required adjustment.
(3) Press EXIT to save the setting.
(4) Once all required adjustments above been made,
press EXIT again to exit from the parameter menu.
18-inch Flat Panel Dis play
Front Panel Con trol and In di ca tors
61 The 18-inch Flat Panel Display is fitted with the
following controls and indicators:
(1) Display POWER ON/OFF switch, located on the
front panel of the unit.
(2) BRIGHTNESS control, located on the front panel.
(3) POWER (Green) LED - indicates Power ON. The
green POWER status indicator extinguishes and
the amber NO SYNC indicator illuminates when in
Power Save Mode.
(4) NO SYNC (Amber) LED - indicates that the
monitor cannot synchronise to the external video
input and has entered the power-save mode.
On-Screen Ad just ment Con trols
62
The Display can be adjusted using an On-screen
Display (OSD) and the following pushbutton controls:
(1) MENU - enables the Main Menu to be opened and
closed.
(2) RESET - allows exit from menu selections.
(3) UP/ DOWN Arrows - used to select a sub-menu
and to make adjustments once a function is
selected.
63
The On-Screen Display (OSD) facilities provided by
the 18-inch Flat Screen Display are shown in Figure7.
64 For the best picture setting, a suitable test image of the
required resolution should be used. Set up the monitor
as follows:
(1) Press the MENU key to open the Main Menu.
(2) Open the required sub-menu, using the [+] (up)
and [-] (down) keys
65
In the event that the unit comes up in the wrong
resolution format (SXGA vs. XGA), use the following
procedure to correct the situation:
(1) Press the Menu pushbutton and turn the power
ON. Keep the Menu pushbutton depressed for
several seconds, until a sub-menu is displayed.
The sub-menu shows SXGA and GA for selection.
(2) Select the required resolution.
(3) Press the [+] pushbutton. The correct format is
selected and the sub-menu disappears.
Original 8c.15 May 01
KH 2020
Chap 8c