Smithco Sand Star Zee 45-501-A, Parts & Service

Page: 45 / 69

43
Accessories
45-503 84" RAKE ASSEMBLY PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1* HB-58-11-400 Bolt,
5
/
8
- 11 x 4 2
HMB-58-14 Machine Bushing,
5
/
8
x 14GA 2
HNCL-58-11 Lock Nut,
5
/
8
- 11 2
2 45-588 Draw bar 1
3* HCP-12-150 Clevis Pin,
1
/
2
- 1
1
/
2
2
4* HP-18-100 Cotter Pin,
1
/
8
x 1 2
5 76-275 Spacer 2
6 45-590 Right Rake Frame 1
7 45-586 Grooming Blade 3
8* HB-516-18-075 Bolt,
5
/
16
- 18 x
3
/
4
6
HNFL-516-18 Flange Lock Nut,
5
/
16
- 18 6
9* HBFL-516-18-075 Flange Lock Bolt,
5
/
16
- 18 x
3
/
4
20
HNTL-516-18 Nylon Lock Nut,
5
/
16
- 18 20
HW-516 Flat Washer,
5
/
16
20
10 13-757 Rake Connect Strap 10
11 45-589 Center Rake Frame 1
12 13-443 Finishing Blade 2
13 13-445 Rake Teeth Kit (27 per kit) 1
11-066 Rake Teeth 4
HN-38-16 Nut,
3
/
8
8
HWL-38 Lockwasher,
3
/
8
4
14 45-591 Left Rake Frame 1
15 45-587 Finishing Blades 3
* 13-764 Hardware Kit 1
INSTALLATION INSTRUCTIONS
1� Bolt 31 rake teeth (Ref 13) to frames, keeping all the same length�
2� Lay out rake frames (Ref 6, 11 & 14)� Connect them using clevis pin (Ref 3), Spacer (Ref 5) and cotter
pin (Ref 4)�
3� Attach left frame (Ref 14) and right frame (Ref 6) to draw bar (Ref 2) using
5
/
8
bolt, machine bushing,
and center lock nut (Ref 1)�
4� Attach the three groomer blades (Ref 7), one to each of the rake frames (Refs 6, 11 & 14) using two hex
bolts and flange lock nuts (Ref 8). Slide groomer blades to end of slot and tighten hardware.
5. Attach three large finishing blades (Ref 15) and then the two smaller finishing blades (Ref 12) to the
tabs of the rake frames using two rake connect strap (Ref 10) per finishing blade. Secure, using flange
lock bolt, flat washer and nylon lock nut (Ref 9).
NOTE: Attach Straps using hardware as illustrated, placing Flat Washer on Strap then secure
with Lock Nut� Attaching with the Flange Bolt in contact with the Strap will cause the Strap to
bind and misalign Finishing Blade�
6� Attach the rake to the trap rake quick hitch by sliding the draw bar hitch into the spring loaded locking
mechanism�
7� With the rake on the ground pull the rake to the right side until it is 2-3 inches from the tire�
8� Repeat steps on left side�
9� Turn machine on and test for operation of rake assembly by raising and lowering the rake assembly�
Also with rake down, turn sharp corners to check that rake does not touch wheels�
10� NOTE: Test rake in sand to assure tire tracks are covered by the rake when turning sharp corners in
either direction� If there are tire tracks, readjust using the adjusting screws on the hitch, so the rake
comes closer to the tire�