
11
Ser
vice
SERVICE CHART
The suggested maintenance checklist is not offered as a replacement for the manufacturer’s engine manual
but as a supplement� You must adhere to the guidelines established by the manufacturer for warranty cover-
age� In adverse conditions such as dirt, mud or extreme temperatures, maintenance should be more frequent�
Maintenance Service Interval
Maintenance Procedure
After the first 8 operating hours
•
Torque the wheel lug nuts� (64-74 ft/lb (87-100 Nm))
•
Change the engine oil filter�
Before each use daily
•
Check the engine oil level�
•
Clean area around muffler and controls
•
Check the hydraulic fluid level�
•
Check the tire pressure�
•
Check condition of hydraulic hoses and fittings�
•
Inspect and clean the machine�
Every 25 hours
•
Clean air filter
1
•
Check the battery fluid level and cable connections�
•
Change oil when operating under heavy load or high
ambient temperatures�
Every 50 hours
•
Replace engine oil filter
•
Check muffler and spark arrestor
Every 100 hours
•
Replace engine oil filter
Every 250 hours
•
Change air filter
•
Check tire pressure (5 psi)-Rear� 20 psi - Front�
•
Torque the wheel lug nuts� (64-74 ft/lb (87-100 Nm))
•
Change hydrauilic oil and filter
•
Lubricate machine
Every 400 hours or yearly
•
Replace air filter
•
Replace Pre Cleaner
•
Replace spark plugs
•
Clean air cooling system
1
•
Replace fuel filter
•
Check valve clearance
2
•
Lubricate machine
•
Visual inspection of machine and hydraulic hoses
•
Change oil
•
Torque the wheel lug nuts� (64-74 ft/lb (87-100 Nm))
•
Check battery terminals and electrolyte level
1
In dusty conditions or when airborne debris is present, clean more often
2
Not required unless engine performance problems are noted�
Summary of Contents for Sand Star Zee 45-501-A
